Aim: - Calculate the Concrete Mix Design for M35 grade concrete with fly-ash  I. STIPULATIONS FOR PROPORTIONING OF M35 GRADE CONCRETE a) Grade designation: - M35 b) Type of cement: OPC 53 grade conforming to IS 8112 c) Type of mineral admixture: Fly ash conforming to IS 3812 (Part-1) d) Maximum nominal size of aggregate:…

AIM: To sketch a plan of G+1 floor residential building according to Vaastu Shastra and listing down the names of the structural drawings required to be provided to the construction site.   INTRODUCTION TO VAASTU SHASTRA: Vaastu Shastra is the Ancient Indian Science of architecture and acts as a guideline to design…

Q Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool.Please read the drawings and find out the missing dimensions before working on the sketches.   AIM:  (A) Create the geometries…

AIM: To Creating a Floor plan, Footing detail and Isometric view using AutoCAD. INTRODUCTION: The main objective of this assignment is to get in touch with various tools in AutoCAD like the rectangle, polylines, modifications tools like copy, move, offset and modes like snap mode and ortho mode. These tools will be understood…

AIM: To draw the geometries using Chamfer, fillet tool in Autocad. Commands used: Line, circle, chamfer, fillet, mirror, trim, move, rotate,annotate. DRAWING: 1 Procedure: 1.New sheet- units- decimal-precision 0.00-meter-ok. 2.Limits- 0,0 and 420,210. 3. zoom-All. 4. Select Line tool and draw the lengths starting from…

1. Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors.   Aim: To draw the layout of a residence as…

1. Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left AIM: TO CREATE A COLUMN SCHEDULE. INTRODUCTION: In in given table, a bar bending…

Q1. Draw the elevation and details of a wardrobe as shown in the Figure below. After sketching, you need to provide the dimensions and text with the use of layers. Use proper text styles and dimension methods to document it. Also, assume dimensions, wherever needed. Note: All dimensions are in mm.   AIM: To Draw the elevation…

1. Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required. AIM: TO DRAW PLAN ELEVATION AND SECTION OF THE HOUSE IN AUTO CAD.…

Q: Design and Draft a layout of a residential building with the following details: a. Plot Size: 60’x20’(18.3m x6m)  b. Orientation- Facing East  c. Develop the following: 1. Architectural Drawing (Floor Plan, Elevations, and Sections) 2. Structural Drawing (Column, Bean, Footing Plan)   AIM: Design…

1. Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

Q1. Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards.     Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to…

Q1. Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the layout.…

Q1. Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing.     AIM: TO DRAW THE 3D WIREFRAME MODEL AS SHOWN FIGURE BY USING AUTOCAD TOOL INTRODUCTION: THE 3D WIREFRAME MODEL GIVEN IS A FURNITURE EQUIPMENT IN THE HOUSE. THE 3D WIREFRAME MODEL IS DRAWN IN DIFFERENT COORDINATE…

Q1. Create a 3D Isometric View of the building with plan and elevation given. AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION: • An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. • One of the defining characteristics…

AIM: To create a 3-Dimensional model of the residential building with a rendered view using AutoCAD. INTRODUCTION: 2D Wireframe Model:- A wireframe model is a skeletal description of a 3D object. There are no surfaces in a wireframe model and it consists of only points, lines, and curves that describe the edges of the…

Q1) From the file menu, create a new project (Structural / Architectural / Construction template ) and name the project appropriately? ANS: AIM: To create a new project from the file menu and need to name the project appropriately. INTRODUCTION:  For creating a project, select a template from the Projects list or…

Q1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools. ANS: Building Information Modelling (BIM)- Building information modeling (BIM) is a process supported by various tools, technologies and contracts involving the generation and management of digital representations of physical and…

Q1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

Q1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Ans: AIM: TO CREATE CELLING FROM THE ARCHITECTURE TAB ABOVE THE WALL ST FIRST-FLOOR LEVEL. INTRODUCTION: -  Create ceilings in a ceiling plan view…

Q1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? ANS:  Building codes are a set of laws, regulations and ordinances adopted by a government legislative authority that governs the physical construction of a building. They set formal rules for the design of buildings…

Q1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project ANS: AIM: To set project base point and project shared coordinates for the project in architectural template. PROCEDURE:  step 1: click on Revit 2021, avalible on homescreen. let it get…

Q1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School   AIM: To select the type of structure you want to build from one of the given. ANS: I would…

Q1) What are HVAC systems? Why are they essential in the modeling of buildings? ANS: HVAC systems represent Heating, Ventilating and Air Conditioning • HVAC systems are, everything from air conditioner at home to the large systems used in industrial buildings and apartment blocks. A good HVAC system means, they give…

Q1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below           a. Using 3D model create a section box           b. To create similar doors and windows in a floor plan layout         …

Creating Conceptual Mass In Revit And Creation Of Sinusoidal Curve And A Parametric Stadium Using Dynamo   Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code; while also creating an algorithm…

Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork Used primarily in construction industries to complement 3D Design packages Navisworks allows users to open and combine 3D models, navigate around them in real-time and review the model using a set of tools including comments, redlining, viewpoint,…

Question 1:What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate   AIM: TO IDENTIFY the mode of failure or damage of the beams in the given figure a)   Type: From the above image we can say that, this Crack is formed due to flexural failure in beams.…

Question 1: Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3 DOFs as shown. Assume L = 2h and Elb = Elc   AIM: To Compute lateral stiffness of the one story frame with an intermediate realistic stiffness of the beam. The system has 3…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy, bi-directional stiffness and ductility. ANS: By observing the given layout we can comment on following aspects:…

Question 1: The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

AIM: To Model a 25 storey building on ETABS with structural properties as specified below and to cross check the parameters as per IS 1893 Provisions. PROCEDURE: STEP: 1 Go to ETABS software  click on the file menu click on creat new model option A new model dailouge box will be open as model intialization.  …

Ouestion: Task: Effect of stiffness on T: Compare fundamental natural periods of buildings E & Fas well as G & H. Why is there a marginal or significant difference in the fundamental natural periods? Effect of mass on T: Compare fundamental natural periods of buildings H, J and K. Have the buildings become more…

OUESTION : Detail design of beams in Etabs 2018.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A   …

QUESTION: Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for…

OUESTION: The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length and…

QUESTION: The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been…

QUESTION: Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial…

QUESTION:1 Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. ANS: AIM: To Analyze and designthe isolated footing from week 11 challenge on SAFE To verify the size, depth and steel provided as per calculations.  …

QUESTION: In this project, participants will get to experience the entire design process from modelling, analysis, design and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam Function…

 QUESTION:1. Summarize the user interface in TSD with the for the following items: - Project Workspace – How to access and usage  Scene Content – Demonstrate the use of scene content Create two scene views Loading drop list- How to access  Properties windows – how to access and usage  …

 QUESTION: 1 Create column properties for different types of pedestal members and model in the grids created as per the assignment 1 ANS: AIM: To Create column properties for different types of pedestal members and model in the grids created as per the assignment 1   PROCEDURE: STEP: 1 Open the Tekla Structure…

QUESTION :1  Create beam properties for First floor and model the beams   ANS: AIM: To Create beam properties for First floor and model the beams   PROSEDURE: STEP: 1 Go to TDS software Open the challenge 2 file   STEP: 2  go to home tab < Manage Properties sets property set tab will appear…

QUESTION: 1 Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m  ANS: AIM: To Calculate dead load in design report based on IS code and apply dead…

QUESTION: 1 Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 ANS AIM: To Generate manual wind loading in the design report based IS code as per the given input TOOLS USED: • Excel • IS codes. • Calculator. PROCEDURE: 1.…

1. Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model AIM : Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model.   PROCEDURE :  STEP : 1 Open TDS software Open the model from previous …

ASSIGNMENT: Analyze and design a steel building to 10T CRANE as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. Provide bracings and moment connection for lateral stability.  Consider dead, live, equipment and wind loading. Consider the brick wall loading for 150mm thick and…

1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm     AIM: To Setup model for RC building design and based on following parameters for cover as mention…

1.  Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load   AIM: To calculate dead load in design based on IS Code and apply on model.   CALCULATION: Finish loading finish load (50 mm Thickness…

1. Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly.   AIM: To generate seismic loading based IS codal provisions and zone II.   INTRODUCTION: Seismic load indicates how much seismic energy (waves of energy that travel through the earth) a…

Que:   Based on the analysis design RC column and beam.   AIM: To run the analysis of the structure and design reinforced concrete beam and column   *********Design of Reinforced Concrete COLUMN*********   INTRODUCTION: The structural design of reinforced concrete (R.C.) columns involves the…

Que:  Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations).   AIM: To design the slab and foundation of the model.   INTRODUCTION: The design of a slab is based on the thickness of slab, size of bars, distances of…

1. Generate report for the steel building design from challenges 1 – 6 along with the loading summary   AIM: To Generate report for the steel building design from challenges 1 – 6 along with the loading summary.   PROCEDURE: STEP: 1 Open TDS software Click on open  Select the previous file…

Develop general arrangement for the RC office building. Analyze and design the building as per IS standard code in TEKLA STRUCTURAL DESIGNER. Refer the attached plan and elevation. The building to be designed for dead, live, wind and seismic loading. Report of each member to be generated and extract drawings for structural…