Workshops Projects Blogs Careers Hire from us Corporate Training  All Courses

Choose a category

All Courses / undefined

All Courses / undefined / undefined  Corporate Upskilling

FOR Universities

More

# Frequency Analysis of a rotating shaft Using SolidWorks

AIM : To find out the critical frequencies of a rotating shaft in Solidworks. OBJECTIVES : To create 3D model of a rotating shaft. To perform frequency analysis on the rotating shaft and find out the critical frequencies. INTRODUCTION : For a rotating shaft there is a speed at which, for any…

Project Details

Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.

Be the first to add a comment

Read more Projects by Sourabh Lakhera (21)

Week 3 - 2D meshing for sheet metal

Objective:

2D meshing and pre-processing for Car hood Metal Sheet   OBJECTIVE:- Starting with the given Component (in 3D) of Automobile Car Hood, Performing Geometry clean-up and after Generating the Mid-Surface of the Model, then proceeding with Meshing of the Components under the Quality Criteria to meet the requirement of… 07 Jul 2021 02:37 PM IST

• ANSA

Modelling and simulation of flow through a flowbench Using SolidWorks

Objective:

AIM: To create a 3D model of a flow bench and run flow analysis. OBJECTIVES : To obtain a plot of valve lift versus mass flow rate. Find the effect of valve lift on the mass flow rate. To run a parametric study for various valve lift. INTRODUCTION :  An airflow bench is a device used for testing… 17 Jul 2020 01:47 PM IST

Frequency Analysis of a rotating shaft Using SolidWorks

Objective:

AIM : To find out the critical frequencies of a rotating shaft in Solidworks. OBJECTIVES : To create 3D model of a rotating shaft. To perform frequency analysis on the rotating shaft and find out the critical frequencies. INTRODUCTION : For a rotating shaft there is a speed at which, for any… 17 Jul 2020 01:44 PM IST

Solving second order Differential Equations using Python

Objective:

AIM:  To simulate the transient behavior of a simple pendulum and to create an animation of it's motion. OBJECTIVE :  To write a program in Python that solves the second-order ODE corresponding to the motion of a simple pendulum and to plot its angular displacement and angular velocity wrt time. To… 17 Jul 2020 01:32 PM IST

Flow over an airfoil Using SolidWorks

Objective:

AIM :  To model the flow over an airfoil for various angle of attacks. OBJECTIVES : To model the flow over an airfoil which can be obtained from here - airfoil data To compare the lift and drag forces for the angle of attacks 0,2,4,6,8,10 degrees. INTRODUCTION : An airfoil is… 17 Jul 2020 01:21 PM IST

Air standard Otto Cycle using Python

Objective:

AIM:  To write a program in Python to solve an Otto cycle and make plots for it. OBJECTIVE : To solve and find out different state variables in the Otto cycle and plot its a p-V diagram. To calculate the thermal efficiency of the given Otto cycle. THEORY: The Otto cycle is the perfect cycle for sparkle… 17 Jul 2020 08:17 AM IST

Centrifugal pump design and Computational flow analysis Using Solidworks

Objective:

AIM: To design and analyze a Centrifugal Pump. OBJECTIVES : To create a 3D model of a centrifugal pump. To obtain the relationship between Pressure ratio and mass flow rate using a Performance diagram. THEORY: Centrifugal Pumps are the most popular and commonly used type of pump for the transfer of… 16 Jul 2020 03:13 PM IST

Data analysis using python

Objective:

AIM: To write a script that does data analysis on python. OBJECTIVE : Visualizing the data, i.e., to plot a graph between any two quantities according to the user's input. Compatibility Check, i.e., code should exit gracefully, if a non-compatible file is provided as an input. To calculate basic engine performance… 15 Jul 2020 02:49 PM IST

Curve fitting using python

Objective:

AIM : To write codes in Python to perform curve fitting. OBJECTIVE :  To wite codes to fit a linear and cubic polynomial for the Cp data. To plot the linear and cubic fit curves along with the raw data points. To measure the fitness characteristics for both the curves. THEORY : Curve fitting… 15 Jul 2020 02:48 PM IST

Flow over a cylinder using SOLIDWORKS

Objective:

AIM : To simulate the transient state flow over a cylinder. OBJECTIVES : To run a baseline simulation and then calculate the Reynolds number.  To increase the Reynolds number by a factor of 20%, 40%, and 100% then run the transient flow simulation. INTRODUCTION :  Steady State Transient… 14 Jul 2020 08:47 AM IST

Analysis of Shell And Tube Heat Exchanger(Epsilon-NTU Method) using MATLAB [INDEPENDENT PROJECT]

Objective:

Aim  :- To compute the Performance parameter of Heat Exchanger using Epsilon-NTU method.   OBJECTIVE : ·       To calculate Effectiveness, based upon NTU(No. of transfer unit), and Capacity rate ratio(Crr). ·       To… 12 Jul 2020 07:22 AM IST

Robot's Manipulator Kinematic Study and Workspace Visualization

Objective:

Robot’s Manipulator Kinematic Study and Workspace Visualization. AIM: To visualize the simulation to analyze. To have understanding of workspace with the help of kinematics study of Manipulator (2d). GOVERNING EQUATIONS IF ANY: - The transformation matrix T for the end-effector with respect to the coordinate frame… 27 Jun 2020 04:02 AM IST

Parsing NASA thermodynamic data Using MATLAB

Objective:

AIM : -To write a program in MATLAB for parsing NASA thermodynamics data. OBJECTIVE : 1.      Making of a MATLAB code to extracts 14 coefficients by reading NASA Polynomial format as a .dat file. 2.      From the given DATA file calculating Molecular weight of each species… 16 Jun 2020 12:02 PM IST

Rankine's cycle Simulator MATLAB CODE(Depending UPON the given INPUT)

Objective:

AIM : To create a Rankine Cycle Simulator using MATLAB. OBJECTIVE : To calculate the state points of the Rankine Cycle based on user inputs.  To plot the corresponding T-s and h-s plots for the given set of inputs. THEORY :-               … 16 Jun 2020 12:01 PM IST

Multi-Body Dyanamics and Simulation of IC Engine's Valve Train Using SolidWorks

Objective:

AIM : To model the Valve Train components for IC Engine and assemble than to get the simulations in Solidworks According to the Following cases. OBJECTIVES : To get results while performing Motion study simulations for different cam heights. S.No. CAM lift (mm) Speed (RPM) Material 1. 3.5 1500 Cast Carbon… 16 Jun 2020 12:00 PM IST

MBD Simulation on a Piston Assembly Using SolidWorks

Objective:

Multi-Body Analysis On Piston Assembly   AIM :-  To Model Piston-Assembly  and then assemble them in SolidWorks. The motion analysis Of the Piston-Assembly is carried out in three different Offset cases.. OBJECTIVE :- To create 3D model of different components of piston assembly, To run motion study analysis… 16 Jun 2020 11:58 AM IST

Design and Motion Analysis of Planetary Gear Train Using SolidWorks

Objective:

AIM :- To design and run the simulation of Planetary Gear train using SolidWorks. Obejective : - ·        To create internal ring gear with following properties - Module = 2.5 (ANSI METRIC must be used while selecting Gear train). Number of teeth = 46 ·       … 11 Jun 2020 10:53 PM IST

SolidWorks simulation of Internal Geneva Mechanism with Motion Analysis

Objective:

AIM : - Simulate Multibody Dynamics of Internal Geneva Mechanism using SOLIDWORKS.   OBJECTIVE : -   Create cad models of Internal Geneva Mechanism in SOLIDWORKS Create an assembly of Internal Geneva Mechanism in SOLIDWORKS Simulate Multibody Dynamics of Internal Geneva Mechanism using SOLIDWORKS at… 07 Jun 2020 03:01 PM IST

Curve Fitting Using MATLAB for Specific Heat vs Temperature Actual realistic Curve.

Objective:

AIM Write a program to suit a linear and cubic polynomial for the Cp data and measure the fitness characteristics for both the curves. OBJECTIVES ·       A MATLAB code to suit a Linear and Cubic Polynomial for the given DATA, ·       Plot the comparison… 24 May 2020 05:06 AM IST

ANIMATION OF PENDULUM USING MATLAB, BY Solving second order ODE

Objective:

SIMPLE PENDULUM A pendulum is a weight suspended from a pivot so that it can swing freely. When a pendulum is displaced sideways from its resting, equilibrium position, it is subject to a restoring force due to gravity that will accelerate it back toward the equilibrium position. The second order ODE use the following… 10 May 2020 01:50 AM IST

Air standard Otto Cycle - PV diagram using MATLAB Code, Also Evaluation of Thermal Efficiency of the cycle

Objective:

AIM: Derivation of PV diagram using MATLAB Code and also calculating the Thermal Efficiency of the cycle GOVERNING EQUATIONS IF ANY:  Ideal Gas Equation PV =mRT where : - P –Absolute Pressure (in Pa)                       … 09 May 2020 09:51 PM IST

Showing 1 of 21 projects
Try our top engineering courses, projects & workshops today!