Hood design-Week 2

Aim :         To develop the car Backdoor(Tail gate) with the reference of given skin data as per engineering standared by using NX12 Back Door :          The Back door is typically hinged, but sometimes attached by other mechanisms such as tracks, in front of an opening which is used for entering and exiting a vehicle. …

Question: For the Given Roof styling, create an ASSEMBLY by developing the essential flanges for the outer roof and creating the reinforcements. Provide appropriate dimensions and check for Draft analysis. Do a curvature study on the roof and perform calculations to determine the position of the Bow-roofs. Suggest and…

Report On Section Modulus Calculation Of Hood Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes to bending.…

  FENDER DESIGN REPORT Aim:    To design the BIW(Body In White) of the front fender using the fender skin data master section as the given data by using NX CAD. Fender:      Fender is the American English term for the part of an automobile. The fender is a part of an automobile that covers the wheel to prevent sand, mudstone,…

AIM : To design the hood of a car with the given input Outer panel and its dimensions. Hood Introduction : The hood (North American English) or bonnet (Commonwealth English) is the hinged cover over the engine of motor vehicles. Hoods can open to allow access to the engine compartment or trunk (boot in Commonwealth English)…

Aim:      This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards.  Fender Wheel Arch: Fender Wheel Arch is the sem-circular part positioned above the wheel of the vehicle. The most important body was a change that the…

Objective: To write a one-pager about Under-Body Coating and its purpose, its types in detail, and its pros and cons. UNDERBODY COATING Definition: Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term…

QUESTION: 1. Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members including his wife, a five-year-old boy, his father, and his mother. He visits his native place Madurai…

Aim: To develop a mechanical design of battery pack based on the required energy capacity Nanophosphate High Power Lithium Ion Cell ANR26650M1-B: A123’s high-performance Nanophosphate lithium iron phosphate (LiFePO4) battery technology delivers high power and energy density combined with excellent safety performance and…

Objective: A)To run three test cases from harness dashboard of closed loop BMS control. B)To explain coulomb counting for finding the SOC estimation in BMS.  Downloading and open closedloop BMS harness dashboard model: In file exchange open the document of 'Design and Test Li-ion Battery Management Algorithm'. Download…

1.Prepare a table which includes materials & chemical reactions occurring at the anode and cathode of LCO, LMO, NCA, NMC, LFP and LTO type of lithium ion cells.Give your detailed explanation on it. Introduction: Lithium-ion Cells are a secondary type of battery cell that is they are rechargeable and also they are reusable…

Aim: To prepare a technical report of Simulation of BAJA All-Terrain Vehicle (ATV) under different conditions. Objectives: Carry out a system-level simulation of an all-terrain vehicle and prepare a technical report explaining the model properties & comments on the results. ALL TERRAIN VEHICLE: An all-terrain vehicle…

Objective: 1.Implement control logic of a “washing machine” using Stateflow as per given sequence: If the power supply is available, the system gets activated If the Water supply is not available, stop the process & indicate through LED Soaking time should be 200s followed by Washing time of 100s. Then…

1.Make a Simulink model of Doorbell using solenoid block with the following details: Here first we are going to study the Simulink model of the doorbell using a solenoid block. We need to access the Simulink with the block parameters to run the simulation. First, we need to get to understand the theory behind…

Objective: To Simulate a Rankine cycle using matlab. Extracting Steam and water properties from XSteam data (IAPWS IF - 97 standard) Calculating all the state points of the cycle based on User inputs. Plotting the T vs s and H vs s plot for the given input.   Rankine Cycle: Rankine cycle is an idealized thermodynamic…

Aim: To write a code in Matlab to parse the NASA thermodynamic data file and then calculate the thermodynamic properties of various gas species. Objective : 1. To write a function that extracts the 14 coefficients and calculates the enthalpy, entropy, and specific heats for all the species in the NASA thermodynamic data…

A genetic algorithm (GA) is a method for solving both constrained and unconstrained optimization problems based on a natural selection process that mimics biological evolution.The algorithm repeatedly modifies a population of individual solutions. At each step, the genetic algorithm randomly selects individuals from the…

% Objective: Solving second order ODEs of a penedulum clear all close all clc b = 0.05;0 g = 9.81; l = 1; m = 0.1 % initial condition theta_0 = [0;5] % time span t_span = linspace(0,10,500) % solving ODE [t,results] = ode45(@(t,theta) ode_func(t, theta, b,g,l,m), t_span, theta_0); %Plotting figure(1) hold on plot(t,results(:,1))…

%ANIMATION OF KINEMATICS OF DOUBLE LINK ROBOTIC ARM clear all close all clc %inputs l1=1; l2=0.5; theta1=linspace(0,90,40); theta2=linspace(0,90,40); ct=1; for i=1:length(theta1) THETA1= theta1(i); for j=1:length(theta2) THETA2=theta2(j); x0=0; y0=0; x1=l1*cosd(THETA1); y1=l1*sind(THETA1); x2=x1+l2*cosd(THETA2); y2=y1+l2*sind(THETA2);…