Photo Realistic Rendering

AUTOMOTIVE DESIGN OF CAR BACK DOOR USING NX CAD OBJECTIVE: i) From the given styling surface, develop a back door using appropriate design methodologies. ii) The objective of this project is to design a BIW Back Door of a car with an Inner Panel, Outer Panel, and Reinforcements for the Hinges, Gas stay, Wiper Motor, and…

Roof Design: This report is about the roof design done with respect to the inputs like styling surface, master sections of various parts, design parameters, and andards used. Objectives: Create a Car Roof model based on the styling surface, master sections given for various parts with mastic points and reinforcements.…

Introduction: A fender is the curved portion of the car's body that sits over and houses the wheels. The purpose of a fender is pretty simple. Its purpose is to keep mud, rocks, and other road debris from being thrown around by the tires. In other words, the fender is a housing for the wheels that keeps road debris contained.…

OBJECTIVE: To increase the Section Modulus of the hood by necessary changes using NX cad. SECTION MODULUS: It is termed as the ratio of the second moment of area and distance from N.A (Neutral axis) to the extreme fiber. Also, it is the measure of the strength of the given member. The stress in the outermost section of…

Report On Clearance Check for Front Fender And Wheel To The European Regulation. For the European regulations These four points should dear a safety gap of 10mm. The points will be at 1st at 30 deg forward from the wheel center on wheel outer dia 2nd at 50 deg rearword. 3rd at 150mm above wheel center, intersecting at…

Objective: To design outer panel of Hood with Hem and develop the Inner panel with all necessary reinforcements definition then positioning of Hinge, striker and create provision for mastic sealant points. Theory: The Hood or the Bonnet of a car is considered as the frontal BIW enclosure component. Bonnets are designed…

Under Body Coating (UBC): What: Under body coating is a type of automotive coatings like paint, primer protective coatings, etc. Often neglected UBC plays a vital role in service life of a Car. It is mandatory to have a standardised amount of UBC for homologation in markets around the world with variations in the layer…

                                                          BENCHMARKING-REPORT ON CARS   OBJECTIVE: Picking up a car as per customer's requirement with the help of Benchmarking.…

                                                           SHEET METAL BRACKET II DESIGN USING NX OBIECTIVE The aim of this project to design a metal bracket and create a…

Tittle of the Project:- Advanced Sheet Metal Design Using NX CAD _Bracket. Objective: To design a Bracket by using Siemens NX12 Sheet metal application. Introduction: For creating metal bracket from 2D drawing i have used various tools in NX Cad. I have used tools such as contour flange, normal cutout, break corner, unbend,…

Title: Project report on modelling of Odd shaped enclosure using NX CAD Objective: To design 3D CAD model of Odd shaped enclosure using NX 12 Introduction: NX is the the most powerful, flexible, and innovative product development solution in the industry. NX for Design has the features. performance, and capabilities to…

  Title: Project report on modelling of box aseembly using NX CAD Objective: To design 3D CAD model of box assembly using NX 12 Introduction: Sheet metal is metal formed by an industrial process into thin, flat pieces. Sheet metal is one of the fundamental forms used in metalworking, and it can be cut and bent into…

OBJECTIVE: Design casing in sheet metal workbench using nx cad. INTRODUCTION: Casing may refer to an enclosing shell, tube or surrounding material. it may also refer as • Casing borehole, metal tube used during the drilling of a well Casing molding, decorative molding surrounding door or window openings • Casing…

AIM - To design a Door Panel of an Automotive using CATIA V5. OBJECTIVES - • To create an assembly and organize different surfaces of the given class A surface into different parts of the door trim panel. To create a tooling axis and perform a draft analysis on the class A surface of each part. To create class B,…

  DESIGN AND ASSEMBLY OF QUICK RETURN MECHANISM: QUICK RETURN MECHANISM A quick retum mechanism is an apparatus to produce a reciprocating motion in which the time taken for travel in retum stroke is less than in the forward stroke. It is driven by a circular motion source (typically a motor of some sort) and uses…

AIM: To design a B pillar with the given mastersection to follow the design criteria and thickness and thereby devolop a closed volume part. INTRODUCTION: biswasvikas The B-pillar is the post between the front and back seat doors of a car, connecting the roof to the body. It can also be defined as the vertical roof support…

AIM: Creating the Door Arm Rest component through the given Class-A surface of 2.5 mm thickness with the tooling axis meeting the requirements of the draft angle and at the end performing the Draft analysis on the model. PROCEDURE REQUIRED DRAFT ANALYSIS: STEP 1: Ensure there is no gap between the two neighbouring surfaces.…

Aim: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface is created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the Heat Stakes and the locators considering the design rules.…

DESIGN RULES FOR SCREW BOSS AND DOG HOUSE FEATURES: AIM: to design screw-boss and dog house on the coin holder considering every design rules in the industry. TOPICS COVERED: 1. Creation of tooling axis 2. Design of screw boss 3. Desgin of dog house 4. Draft analysis report on dog house. THEORY: Class-B surface contains…

Aim To create an out featured rib on the centre console coin holder. Procedure Firstly open the coin holder using the open command Rib To create a rib first extract the base surface of the coin holder. Create a positioning sketch draw a line, constraint it and define it as an output feature. Extrude the output line using…

AIM:   To create a switch bezel from the given A-class surface by considering a thickness of 2.5 mm and also creating Core and Cavity blocks for it. PROCEDURE: A class surface: The input of the product designer is in the form of the A-class surface. The job of the product designer is to create the 8 and C surfaces…

Aim: The aim of this project is to create a tooling axis for the given part and to make it a solid body of prescribed thickness. Objectives: Using the given Class A surface, create a tooling axis and make it a solid body of prescribed thickness. Design Methodology with images: Procedure for creating Tooling Axis 1. Intersect…

DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL: OBJECTIVE: • The objective of the project is to create the class B and C surface for the Base bracket with the given Class-A surface to design a component and carry Draft Analysis by creating the tooling direction for the given Class-A surface. DESIGN A COMPONENT USING B…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.   GIVEN CLASS A SURFACE: TREE STRUCTURE for creating…

DRAFT ANALYSIS ON A FAN COVER OBJECTIVE To perform draft analysis on an imported model (Fan cover) in CATIA INTRODUCTION Injection Molding It is a manufacturing process used for the mass production of plastic components: It works by injecting molten material (plastic) into a mold Under the application of heat and pressure,…

MODELING AND ASSEMBLING THE YACHT MODEL     INTRODUCTION A yacht is a sailing or power vessel used for pleasure, cruising, or racing. There is no standard definition, so the term applies to such vessels that have a cabin with amenities that accommodate overnight use. To be termed a yacht, as opposed to a boat,…

  SKILL LYNC       PROJECT REPORT   MODELLING OF AMERICAN CHOPPER ON SOLIDWORKS                   BY, Vikas Biswas INTRODUCTION This project explains about the designing of different parts of chopper and assembling them to get a complete model of the…