AIM:  To calculate the concrete mix design for M35 grade concrete with fly ash & M50 grade concrete without fly ash.   OBJECTIVE:   The objective of this project is to produce a mix design for M35 grade concrete containing fly ash and M50 grade concrete. The mix will be prepared as per IS METHOD:…

    Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column, Beam, Slab, etc.,) and accordingly calculate the individual corresponding loads…

AIM: To create a Floor Plan, Footing Detail, and Isometric view of Steps and Gable Wall in Autocad. INTRODUCTION: The main objective of this assignment is to get in touch with various tools in AutoCAD like the rectangle, polylines, modifications tools like copy, move, offset and modes like snap mode and ortho mode. These…

  AIM: Drafting of various geometries using chamfer,fillet tool in AutoCAD    introduction: AutoCAD consists of a number of drawing and modification tools. Among the modification toolss are chamfer,fillet,offset,object snap, rotate,copy,move,mirror,trim,entend and join Chamfer: A chamfer is an angled line…

1. Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors.     Aim: To draw the layout of a residence…

1.AIM : To create a column schedule asshown in the figure by using auto cad.   INTRODUCTION: introduction: AutoCAD consists of a number of drawing and modification tools. Among the modification toolss are chamfer, fillet,offset,object snap, rotate,copy,move,mirror,trim, entend and join Chamfer: A chamfer is an angled…

Aim: To draw the elevations and deatails of wardrobe as shown in figure   introduction: AutoCAD consists of a number of drawing and modification tools. Among the modification toolss are chamfer,fillet,offset,object snap, rotate,copy.move,mirror,trim,entend and join Chamfer. A chamfer is an angled line that meets the…

1) Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required.     introduction: AutoCAD consists of a number of drawing and modification…

Creating Architectural Drawings. (Floor Plan. Elevations, and Sections) for a plot size of 60'x20' and developing relevant basic structural drawings (Column, Beam. Footing Plan).   Aim: To create Architectural Drawing (Floor Plan, Elevations, and Sections) for a plat size of 60'x20', facing east, and to develop relevant…

Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards. Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen…

Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad   AIM: Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as hown in Figure. Also,…

AIM: To create 3D model view of 1. Furniture Element 2. Isolated footing 3. AASTHO type grider 4. Drop column with panel 5. A wall COMMANDS USED: • Extrude • Offset • UCS • Box • Union • Subtract • Move 3d orbit • Loft • Sweep • Cone • Region • Boundry introduction:…

  Q] Create a 3D Isometric View of the building with plan and elevation given.  AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION: • An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. • One of the defining…

Create a e dimensional model of the residential building with a rendered view. AIM: The aim of this project is to understand the 3D modelling and to develope the 3D model of any house. Introduction:   AutoCAD consists of a number of drawing and modification tools. Among the modification toolss are chamfer, fillet,offset,object…

AIM : TO LEARN BASIC CONCEPTS OF REVIT   Introduction: Revit is a Building Information Modelling software for architects, landscape architects, structural engineeers, mechanical,electrical and plummbing(MEP) engineers, designers and contractors. Revit supports a multidiscipline design process force collaborative design.…

1.BIM What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools. Building Information Modelling (BIM)- Building information modeling (BIM) is a process supported by various tools, technologies and contracts involving the generation and management of digital representations of physical and functional…

Creating Walls, Partition walls and Floors for a residential layout using REVIT 1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create…

Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level AIM: To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION: • The creation of Ceilings within Revit is a very…

Q.1) Select the type of structure you want to build from one of the three below:  a. Multi-Unit Residential Apartment b. Office Buildings c. School ANS 1:- From the above given options the type of structure I want to select is Multi unit residential building. Q2) Assume reasonable assumptions for geographic and location…

1. Using Dynamo creates a set of sinusoidal points and creates a curve and creates a surface out of the curve. Aim:- TO create a sinusoidal points curve and surface using dynamo Procedure: • Go to select new template> select architecture temoplate> press ok • Go to the manage tab and select Dynamo    open integer slider…

PROJECT:- Usage of Navigation tool, Timeliner and Clash Detection test using Naviswork INTRODUCTION: • NAVISWORKS Used primarily in construction industries to complement 3D design packages (such as Autodesk Revit, AutoCAD, and MicroStation) Navisworks allows users to open and combine 3D models, navigate around them…

IDENTIFICATION OF CRACKS The majority of cracks occur when the building or its components or the material of which the building is made upon it’s subjected to forces that are greater than those which it can withstand Cracks may occur in different components of a building due to  External The majority of…

Aim: To differenciate about Static analysis and dynamic analysis with proper representing pictures. Introduction: To differenciate about Static analysis and dynamic analysis with proper representing pictures.  Procedure:  • Dynamic analysis is the process of testing and evaluating a program - while software is running.…

              challenge

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility.       Answer: i) symmetry: • It is observed that…

Question 1: The building shown, 20 x 35 m in plan, has columns on in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same totala 5 x 5 m grid and shear walls (with dimensions shown cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

AIM: To Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. INTRODUCTION:  ETABS is an engineering software product that caters…

Reinforcement Detailing of Beams from ETABS output. Detail design of beams in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span…

The ETABS file for a G+4 building is provided. Run the analysis and design of the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns, from foundation to terrace level. Sketch…

Open up the Model for which You Want to Design the Shear Wall As we all know, the very first step is to locate the file on your computer and open the ETABS model And in our case, the file has been attached to the question So, download the file, save it at an appropriate location within your system, and then open the same…

AIM: - TO STUDY AND COMPAIR THE RESULTS ON, Factors influencing the dynamic characteristics of different storey building for seismic force Factors influencing the Natural Period of different storey building for seismic force Factors influencing the Mode shape of oscillations of different storey building for seismic force…

Structural Modelling of Residential Building using Etabs 2018 QUESTION: The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided. Conceptualize a framing plan layout and then model the…

Design  of shallow foundation (isolated footings)   Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either…

1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. 2. A column of size 600x600 carrying an unfactored gravity load (DL+LL) of 1175 KN is to be supported on pile cap, which ultimately transfers load to the piles underneath.…

 In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: • Location Guwahati, Assam • Function-…

1.1. Write the steps involved to upload a .std file through web mail?  ANSWER:  • Open the staad software and locate the share option  available on the intro screen. • After clicking on the share button, select send mail option.  Then, browse for the. std file on your machine and hit  send.…