Advanced Sheet Metal Design Using NX Cad Challenge_6_Bracket

Automotive Plastic Component: B Pillar RH Cover - Creating CAD Part from Master Sections and Class A as Input Aim: To design plastic B pillar along with B side features using provided class A surface and master sections. Objectives: To create tooling axis for the component. To design class B and C surface from given class…

DOOR APPLIQUE DESIGN WITH ENGINEERING FEATURES AIM: Creating the Driver Door RH Applique plastic component through the given Class A Surface. To begin with, the tooling axis for the given Class A Surface is created to meet the requirements of the draft angle and at the end perform the draft analysis on the model. Creating…

SCREW BOSS AND DOG HOUSE DESIGN INTRODUCTION: Boss features are commonly found in injection moulding designs. They are used to aid in the assembly of moulded parts by providing a channel for a screw. Dog house is a feature that helps you to avoid sink marks. OBJECTIVE: To create the boss and dog house for the center console…

Attachment Rib Feature Creation Designing Plastic Parts For Injection Molding? Ribs Can Help Add Support And Strength. Ribs are a feature in plastic injection molded parts. They are thin extensions that run perpendicular to a wall or plane.  They are commonly used to provide additional support and strength to a part.…

  DRAFT ANALYSIS, PLASTIC COMPONENT MODELING AND CORE & CAVITY CREATION FOR SWITCH BEZEL AIM: To create the tooling axis for class A surface and To perform the Draft analysis for both the given Class-A surface and the final plastic component created. To create the core and cavity design of…

COIN HOLDER DESIGN OBJECTIVE: To perform draft analysis to check if the part has the given draft on its all faces, to determine the tooling axis and design component using the class-A surface as a reference. DRAFT: Draft is a tool used in CATIA to make the faces taper with respect to the tooling axis. Tooling Axis is the…

Title: Creation of Door Arm rest Aim: To create the door arm rest component using the given class A surface of the arm rest and door. Objectives: To create class B and C surface from given class A surface To make solid closed body model using class C surface To perform draft analysis for class A surface and solid body…

DRAFT ANALYSIS AND PLASTIC COMPONENT MODELING FOR SWITCH BEZEL AIM:              To create the tooling axis for class A surface and To perform the Draft analysis for both the given Class-A surface and the final plastic component created. OBJECTIVES: SWITCH BEZEL Explaining the Draft analysis…

Aim:              To Create the tooling axis for the given Fan cover model meeting the requirements of the draft angle and performing the draft analysis on the model. Objective: 1. To ensure proper tree structure is followed. 2. Geometrical sets should have a proper name based on…

DRAFT ANALYSIS AND PLASTIC COMPONENT MODELING FOR BASE BRACKET AIM:             To perform the Draft analysis, Tooling axis creation for both the given Class-A surface and the final plastic component OBJECTIVES: BASE BRACKET Explaining the Draft analysis and the Tooling axis creation. …

MODELING OF COMPONENTS AND ASSEMBLY & RENDERING OF AMERICAN CHOPPER USING SOLIDWORKS   Introduction:          This report contains of modeling and assembly of chopper components and final rendering with detailed explanation using the solidworks software. Objective: The objective…

Automotive Design of Car Roof using NX CAD Objective: The objective of this project is to design car roof with  essential flanges and reinforcements  like ditch area, front roof rail, bow roofs, central roof rail and rear roof rail for the given styling surface Perform a curvature study on the roof and perform…

HOOD DESIGN Objective:                     To design and model the car hood with inner panel outer panel and required reinforcements . Software used: NX 12.0 The following tasks are performed: Develop the inner panel Develop the outer panel with hemming data. Providing…

AUTOMOTIVE DESIGN OF CAR BACK DOOR USING NX CAD OBJECTIVE:            i) From the given styling surface, develop a back door using appropriate design methodologies.          ii) The objective of this project is to design a BIW Back Door of a car with an Inner Panel,…

Fender Design Challenge Aim:           The aim of this project is to design the BIW of a Fender using the fender skin data as the input data and then attach mountings on the fender for attaching it with the surrounding BIW bodies. Introduction:           Fender is the American…

Section Modulus Calculation and Optimization Objective:              The main objective of this project is to learn the basic tools, commands, and the calculation and optimization of the Section Modulus using Siemens NX CAD. The objectives of this project are as follows: To understand…

UNDERBODY OVERCOATING Car Undercoating: No matter the climate, the underbelly of every vehicle needs proper care and protection. Undercoating helps protect your vehicle against rust and corrosion. Seals on the underbelly parts have gotten a lot tighter and more effective at keeping out dust and moisture, but there are…

Benchmarking OBJECTIVE:                Benchmark with presently available cars in the market for the following case. Mr. D.S. Pughazhyendhii is a married man who lives in Bangalore which is a highly crowded city. His Family comprises five members…

Advanced Sheet Metal Design Using NX CAD - Metal Bracket-II Design Objective: The main objective of this project is to design a sheet metal BRACKET II in NX cad sheet metal application workbench. Also, to perform the drafting for the bracket part. Software used: NX 12.0 To design and model the sheet metal Bracket II in…

  Advanced Sheet Metal Design Using NX CAD- Bracket Design Objective: The main objective of this project is to design a sheet metal BRACKET in NX cad sheet metal application workbench. Also, to perform the drafting for the bracket part. Software used: NX 12.0 To design and model the sheet metal casing in NX by using…

  Advanced Sheet Metal Design Using NX CAD- Odd shaped enclosure Objective: The main objective of this project is to design a sheet metal odd shaped enclosure in NX cad sheet metal application workbench. Also, to perform the drafting for the odd shaped enclosure part. Software used: NX 12.0 To design and model the…

Advanced Sheet Metal Design Using NX CAD- Box Assembly Design Objective: The main objective of this project is to design a sheet metal casing in NX cad sheet metal application workbench. Also, to perform the drafting for the BOX ASSEMBLY part. Software used: NX 12.0 To design and model the sheet metal Box assembly in NX…

  Advanced Sheet Metal Design Using NX CAD- Casing Design Objective: The main objective of this project is to design a sheet metal casing in NX cad sheet metal application workbench. Also, to perform the drafting for the casing part. Software used: NX 12.0 To design and model the sheet metal casing in NX by using…

MODELING OF COMPONENTS AND ASSEMBLY & RENDERING OF SUNSEEKER PREDATOR YACHT USING SOLIDWORKS Introduction:          This report contains of modeling and assembly of SUNSEEKER PREDATOR YACHT components and final rendering with detailed explanation using the solidworks software.…