PROJECT: 1D ELEMENT CREATION CHALLENGE AIM: Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF A. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm …
SANJO SEBASTIAN
updated on 20 Oct 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by SANJO SEBASTIAN (13)
Project 1-Meshing of Rear Wheel Holder challenge
Project 1-Meshing of Rear Wheel Holder challenge Aim: Follow the below-mentioned quality criteria, mesh the component given below and assign thickness: Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper 0.5 5 Min. Length 2 Units 6 Max. Length 8 Units 7…
28 Aug 2023 03:04 PM IST
Week 6-Meshing of Hood Challenge
AIM For the given Hood model, Take the mid surface for all the components after checking the geometrical errors and mesh the mid surface with the given element Quality criteria. Target Element Length = 5 Units S.N Quality Criteria Value 1 Aspect Ratio 5 2 Skewness 45 3 Warping 15 4 Taper …
04 Dec 2022 08:05 AM IST
Week 4-1D Element Creation Challenge
PROJECT: 1D ELEMENT CREATION CHALLENGE AIM: Mesh the Given component with the Size of 5 Units. Create 1D elements on the following component with given cross-section and DOF A. Rod element:- Translational DOF should be Constrained with RBE2 link Cross-Section: BOX- Dimension a= 12 mm …
20 Oct 2022 06:52 AM IST
Project - 2 - Meshing on the suspension Assembly
Project-2 For the given assembly, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned for mid surfaces. Use tetra elements to model non-uniform thickness components. Also use Appropriate connections to connect the component as suggested…
30 Sep 2022 05:06 PM IST
Project 1 - 2D meshing on the instrumental Panel
Project 1 - 2D meshing on the instrumental Panel Aim For the given component, check for the geometrical errors and mesh with the given element Quality criteria. After meshing the component the thickness has to be assigned. Write a detailed report on your meshing process and also mention which method you used to extract…
24 Sep 2022 05:56 AM IST
Week - 8 - Morphing
WEEK - 8 – MORPHING AIM: In this challenge, There will be two models. 1) Practice all the Morphing techniques that were shown in the video for Model-1. 2) Perform morphing for the Model-2 and Increase the Height of the Dog houses and Ribs. MORPHING…
16 Sep 2022 06:36 AM IST
Tool Test 1
Aim This tool test carries two models (i.e. Plastic model, Sheet metal model). For both the models, Mid surface should be taken and meshed as per below quality criteria. Thickness should be assigned to both the models. (Refer “Model Requirements” in “Grading Policy” to know what…
17 Aug 2022 09:03 AM IST
Project - Data Handling and Interpolation
V (Volt) I (mAmp) -17.3 -28 -17.1 -24 -17 -19 -16.8 -14 -16.5 -9 -16 -6 -15 -4 -14 -3 -12 -2 -10 -1.3 -8 -1 -5 -0.6 -2 -0.3 -0.2 -0.1 0.09 0 0.19 0 0.27 0 0.39 0.01 0.43 0.03 0.5 0.17 0.55 0.42 0.6 1.23 0.62 1.99 0.65 3.91 Reading the spreadsheet file in MatLab >> VI=xlsread('VI.xlsx') VI = -17.3000 -28.0000 -17.1000 -24.0000…
05 Jul 2022 06:34 AM IST