Week 9 - Attachment Feature Creation - Challenge 2

AIM     To assemble the butterfly valve and apply the GD&T for the assembly PROCEDURE     First import the all required parts in assembly workbench     then give the required constrains to the parts     the assembly is get finsihed     then…

AIM     To Design an car back door and reincforcement from the given outer pannel  Back door      The back door is a hinged door/tailgate at the rear of the vehicle. It may be used for loading and unloading cargo, or to get passengers in and out, in case there are seats present at…

AIM    To create the roof assembly and develop the required flanges from the given styling surface and follow the master section ROOF    An automobile roof or car top is the portion of an automobile that sits above the passenger compartment, protecting the vehicle occupants from sun, wind, rain, and…

AIM      To calculate the wheel arch clearance from the required points and it for europen standard WHEEL ARCH        The wheel arch is the semicircular part positioned above the wheel of a vehicle. The most important body change was that the front wheel arch was cut higher…

AIM           To create a fender design by using the skin data and the master section INTRODUCTION    FENDER           A fender is a curved panel that sits above the wheels of a car and runs from the bumper to its doors.…

SECTION MODULUS               It is the ratio between moment of inertia of the beam cross section about the neutral to the distance of extreme fiber from the neutral axis            Section modulus is a geometric property for a given cross-section used in the design of beams or flexural members S = I/Y Where I = moment…

    Hood       A car hood is an part which is used to cover and protect the engine it also called as bonnet The common material used for manufacturing the hoods are steel,aluminium,fiberglass and carbon fiber   THE DESIGN CONSIDERATION  FOR HOOD ARE     Safety…

UNDER BODY COATING:                      Under body coating is an process which is used to prevent the corrosion of an automobile under body material. the coating will be applied uniformly.                     …

BENCH MARKING:                  Bench marking is the process of comparison between similar products available in market it includes performance,quality,consumer feedback etc BENCH MARKING FOR AVALIABLE  CARS IN MARKET  CASE:        …

AIM :       To create a door trim plastic component with the given A surface and attachements of heat stakes and locators PROCEDURE:       First create a tooling axis with the reference of A surface       Then create a B surface by offseting the…

AIM:     To create door trim side panel as a complete product PROCEDURE:      First to create B surface individual the components required for the door trim pannel with the help of A surface and master section      Before creating B surface create a tooling axis for each component      After compeleting the B surface make…

  AIM:      To create A pillar with the help of master section PROCEDURE:      first create the tooling axis with the help of master section      for creating the B surface offset the given A surface as per the master section then you will get the B surface…

REPORT :             first create the tooling line from the given A surface             create the B surface by offseting A surface you will get the B surface            …

For assembly a product first we have to create the individual parts of the product as per the given parameters. Create the parts with the help of sketcher and part workbench with proper Iso constrained and perform Boolean operation if required  Then open a new assembly workbench  Import the created parts into…

AIM:      To attachement feature (dog house) on the given door trim PROCEDURE:       To perform the attachement feature opertation first we have to create b surface.       for creating the b surface we should offset the class A surface for the given…

AIM:     To create ribs and screw boss procedure:     create a solid body from the class A surface for a thickness of 2.5mm     Now select the positioned sketch and give the reference surface  from the component     Then draw the sketches for the ribs snd…

AIM:    To create a core and cavity block for an switch bazel PROCEDURE: For creating the core and cavity block of an component. First we have to identify the identify core side and cavity side of the component  The A surface is the core side and the B surface is the cavity side,Then Create a parting surface on B surface…

AIM:      To create & draft analysis a bumper from the given class A surface. STEPS:         first we should create the tooling axis from the class A surface.         after created the tooling axis.then offset the class A surface…

REPORT :             To create an coin holder design first we have to create an tooling axis with the help of class A surace.              consider the suitable direction for creating the componet from that…

REPORT              For creating the tooling axis. first we should identify the suitable tooling direction for making the  component by intersecting the plane yz and class A surface we get an sketch as output in that sketch draw a line on both side on the drafted line as shown in…

REPORT:               By taking ofseted surface as a reference we can create a midpoint and axis system.                From the help of axis system we can create the tooling direction…