Here I have shortlisted some cars which are relatively suitable for MR.PUGHAZHYENDHI. TOYOTA GLANZA TATA PUNCH KIA SONET NISSAN MAGNITE HONDA AMAZE MARUTI SUZUKI DZIRE The below given table have some data which will be ease to compare,   TOYOTA GLANZA TATA PUNCH KIA SONET NISSAN MAGNITE   HONDA AMAZE MARUTI DZIRE…

UNDERBODY COATING: Underbody coating is usually a dense cladding applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted. This is because it can prevent further damage to the undercarriage.  very thick undercoating can soften the noises that reach the cabin. car comes with…

CAR HOOD DESIGN:             As per the given data and the structure, I designed the Hood outer panel, inner panel, Striker, Hinges and Emboss structures.                                                     …

  SECTION MODULUS OF HOOD  OBJECTIVE: To find the section modulus of the hood and optimisation to improve the overall section modulus.   SECTION MODULUS: Section modulus is a direct measure of strength of any sectional area of an object about a reference axis. This strength can be measured directly from Section modulus…

WHEEL ARC             Wheel Arch is the semi-circular part of the fender positioned above the wheel of the vehicle. The design of Wheel arch of a fender should be such that it must shield wheels and protect both passenger’s compartment and pedestrians from projection…

DESIGN OF CAR FENDER FENDER:             It is the part of an automobile, motor cycle or other vehicle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other road spray from being thrown into…

ROOF ASSEMBLY OBJECTIVE:             Main objective of the project is to create the Roof Sheetmetal design in NX cad, and also designing front roof rail, rear roof rail, bow roof (front and rear), centre roof rail and needed reinforcement are creating to build the…

DESIGN OF BACK DOOR   OBJECTIVE:             To design the back door of the car and make the inner panel for the back door and also design the necessary reinforcements.   BACK DOOR:             A…

BASE BRACKET DESIGN   AIM:             The main aim of this challenge is to create the Base Bracket Plastic component through the above-given Class-A surface, by giving the 'Tooling axis' and 'Draft analysis' to the class-A surface of the base bracket.  …

SWITCH BEZEL AIM:             The aim of the project is to create a switch bezel plastic component using the given class A surface following the OEM standard. and perform the draft analysis.     CLASS-A SURFACE:                        …

COIN HOLDER DESIGN   AIM:                         To Create the Coin Holder Plastic component through the given Class-A surface. The tooling axis for the given Class-A Surface should be created meeting…

BUMPER PLASTIC COMPONENT   AIM:           To create the Bumper Design Plastic component through the given Class-A surface.   CLASS A SURFACE:           Class a surface made by the designer which is given as an input to the…

DOOR TRIM LOWER   AIM:           To create the door trim component through the given Class-A surface. Desired thickness of the plastic component is 2.5mm.   CLASS A SURFACE:           Class A is an aesthetic surface with…

SWITCH BEZEL AIM:             The aim of the project is to create a switch bezel plastic component using the given class A surface following the OEM standard. and perform the draft analysis.     CLASS-A SURFACE:                        …

ATTACHMENT FEATURE CREATION (RIBS & SCREW BOSS)     AIM: To Create the tooling axis for the given Class-A Surface meeting the requirements of the draft angle. To Attach B side Features in the component. To perform the Draft analysis on the model.    TOOLING AXIS: Intersect the yz plane with respect…

ATTATCHMENT FEATURE CREATION 2   OBJECTIVE:  To create the Door Trim Plastic Component from the given Class A Surface & then create two dog houses as attachment features for it while following the given Design Guidelines.     DOG HOUSE Dog house is an engineering feature…

DOOR TRIM LOWER WITH ENGINEERING FEATURES   AIM:           Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle…

A-PILLAR DESIGN WITH MASTER SECTION   AIM: To create the A Pillar Design with the master section given as the intersection sketch with the Class A surface and create the tooling axis and perform the Draft analysis for the final solid part. CLASS A SURFACE:           Class…

ASSEMBLY WORKBENCH AIM: To create the individual part files and then create a complete assembly of those part files in the assembly workbench. After creating the assembly make use of the drafting tools to create a 2D drawing. STEPS FOLLOWED: Create the parts from the given 2D drawings by using surface and part commands.…

DOOR TRIM PANEL AIM:           To create a solid body of Side Door plastic trim including the engineering features using the given Class A surface and master section and adding thickness to the component by Catia v5.   SIDE DOOR:          …

WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELING WEEK 2 CHALLENGE AIM:            To download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench and Define all the necessary properties…

WIRING HARNESS ROUTING & PACKAGING   AIM: Download following cad data (P CLAMP) then to define it as Electrical support using Electrical Part design Workbench and Define all the necessary properties. Download following Back shell cad data then to define it as Electrical back shell using Electrical Part design…

WIRING HARNESS DESIGN IN CATIA V5 AIM:           To route the following harness layout in Electrical workbench then Make assumption for harness bundle diameters and Use Following connectors as shown in layout diagram.           To…

WIRING HARNESS DESIGN IN CATIA V5 - 3D MODELING WEEK 5 & 6 CHALLENGE AIM:           To Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, To Check the bundle…

FLATTENING CHALLENGE AIM:             To Flatten the harness assembly completed in “week 4 challenge” and Place the flattened view on drawing sheet. To Ensure bundles with protective coverings has different visuals on drawing view.   GIVEN DRAWING:…

WIRING HARNES PROJECT 1   AIM:           To Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules shall be demonstrated in design. Apply Protection coverings as required and Prepare & Submit all necessary reports like clearance, Clipping/Clamping selection,…

BACK DOOR WIRING HARNESS AIM:           To Route the Wiring harness on Given car body and prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices shall be demonstrated in design. Apply Protection coverings as required. BACK DOOR:…