Creating a Floor plan, Footing detail and Isometric view using AutoCad

object p-1 

                   CS OF LOAD BEARING WALL OVER SPREAD FOOTING.

 THE FOLLOWING STEPS WERE USE  C.S. OF LOAD BEARING WALL

1. LINE START FROM 1,1

2. @.90,0

3. @0,.25

4. @-.25,0

5. @0,.40

6. @-0.05,.40

7. CLOSE THE LINE AND GET OFFSET IS 0.05 IN BOTH SIDE

8. @-.30,0

9. @0,-1

10. @-.30,-.15 CREATETING THIS STEP CONTINUES IN 4 TIMES 

AND CLOSE LINE TO THE OUTER SIDE OF THE FOOTING.

 que 2 drawing object c-2

ANS - 

                              C.S. ISOLATED FOOTING 

SYMETRIC.

THE FOLLOWING STEPS WERE USE TO MAKE C.S. ISOLATED FOOTING.

1. STARTING A LINE FROM THE 1,1 POINT

2. @0,.15

3. @.38,.25

4. @0,1.60

5. @.16,0

6. @0,-1.60

7. @.38,.25

8. @0,-.15

9. @-.38,0

10. @-.16 CLOSE THE OUTER SIDE

11.SPECIFY A FIRST POINT FROM {1,1}

12. @0,0.04

13 @.38,0

14. @0,2

15. @0.08,0

16. @0,-2

17 @.38,0

18. @0,0.04 CLOSE TE LINE COMMAND.

QUE 3 - DRAW LINE DIAGRAME OF A TWO LINE BUILDING

ans - 

                                            LINE DIAGRAME OF TWO BEDROOM BUILDING

THE FOLLOWING STEPS WERE USED TO DRAW LINE DIAGRAM OF TWO BEDROOM BUILDING

1. @.36,0

2. @0,-.30 MAKE THREE STEPS DOWN IN Y DIRECTION 

3. @1,0

4. @0,-.30 MAKE THREE STEPS IN Y DIRECTION

5. @4.20,0

6. @0,-3.60

7. @-4.20,0

8. @0,.30 MAKE THRE CONTINOUSE STEPS HAVING .30 LEANGTH IN Y DIRETIOMN

9. @-1,0

10. @0,-.30

11. @-3.60,0

12. @0,-3.60

13. FROM POINT 11 WE CEATE A LINE HAVING LEANGTH IS 1.83 IN Y DIRECTION.

que 4 - DRAW A OBJECT WHO SHOW A LOAD BEARING WALL AND DETAILS OF FOUNDATION

ANS - 

                  C.S. OF LOAD BEARING WALL

               SHOWING FOUNDATION DETAILS.

THE FOLLOWING STEPS USE TO MAKE C.S. OF LOAD BEARING WALL.

1. SPECIFYING FIRST POINT IS 1,1

2. @.90,0

3. @0,0.45

4. @-.15,0

5. @0,.40

6. @-0.05,0

7. @0,.30

8. @-0.05,0

9. @0,.60

10. @-0.05,0

11. @0,1

12. @-.30,0

13. @0,-1

14. @-0.05,0

15. @0,-.60

16 @-0.05,0

17. @20,-.30

18. @-0.05,0

19. @0,-0.40

20. @-.15,0

21. @0,-.45 CLOSE

.

 QUE 5 - DRAW ISOMETRIC VEIW OF STEPS.

ANS,  - 

                                              ISOMETRIC VEIW OF STEPS

THE FOLLOWING STEPS WERE USE TO DRAW ISOMETRIC STAIRS.

1. START AND ON ISOMETRIC VIEW FROM LEFT 

2. @ 1,1

3. @.15 UP 

4. @ .30 RIGHT

5. @.15 UP

6. @.30 RIGHT

7. @.15 UP

8. @ .30 RIGHT 

9. @.15 UP

10. @ .30 RIGHT

11. SAMETHING WE DO ON LEFT WAY 

12.. @.15 UP 

13. @ .30 RIGHT

14. @.15 UP

15. @.30 RIGHT

16. @.15 UP

17. @ .30 RIGHT 

18. @.15 UP

19. @ .30 RIGHT

20. AND JOIN ALL CORNER LINE BEETWEEN LEFT TO RIGHT CLOSE .

QUE 6 - DRAW 

ANS - 

                                         ISOMETRIC VIEW OF GABBLE WALL

THE FOLLOWING STEP WERE USE TO DRAW ISOMWTRIC GABBLE WALL.

1. 1,1

2. CHANGE GRID TO Y TO X DIRECTION AND PICK A LEFT ISOMETRIC VIEW

3. @1,0

4. @2.42 AT TOP

5. @1 TO RIGHT

6. @2.42 AT DOWN SIDE

7. @1 AT RIGHT SIDE

8. @3 AT TOP SIDE

9. COPIYING 4 LINE OF .30 LENGTH 2 AT BOTTOM AND TWO AT TOP.

10. TAKE .25  LEANGTH LINE AT TOP AND JOIN BOTH TOP LINE WITH ITS ADGE.