Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad

Drawing1:

Aim:

To Create a layout of the Floor Plan and Section A of the Building and to take a plot.

Introduction:

The given drawings are coverted into PDF and printed for making the Drawing sheets Using the template TutorialmArch.dwt

Procedure:

The Drawings after created in Autocad are converted into PDF using the following procedure:

• A layout is created for the given drawing as per requirement.
• The layout is renamed as per the Drawing name or any other name Convenient.
• New views are created using the VIEW MANAGER in the Drawing for easy viewing of the reqiured PLAN or ELEVATION or SECTION.
• Later the same Drawing is taken as the viewport for making views as per the requirement.
• Firstly the Paper of required dimension is taken.
• It is obtained from PAGE SET UP MANAGER.
• Here it is used to Create New setup or Modify the Existing setup
• Later the paper view can be adjusted in Paperspace by Zooming in or Out.
• Command : PS or PSPACE
• The Plan or section or Elevation is taken in Modelspace and adjusted as per the scale.
• Command : MS or MSPACE
• Generally to represent different drawings in a single sheet,the sheet is made as tiles in the PAPERSPACE.
• Command : MV or 
• UsING the MV command to create the viewport.
• The Drawing is adjusted in the Tiles of the Paperspace using the following command
• Command : PAN
• Templates drawings can also be inserted while plotting.
• Some template drawings which are made as Blocks are also inserted.

For Plotting:

• After finishing all the adjustment in both Paper and Modelspace the Drawing is converted to pdf.
• For printing the Drawing the settings are checked and made ready to print.
• Settings include in the PAGE SETUP are:
• Paper size, Plot Area, Plot style Table, Plot Options , Drawing Orientation ,Plot Scale etc..
• The PDF Drawing is saved in the Folder and named conveniently.
• Finally the Drawing is Printed.

Result:

 The PDFs are attached in the link below

Drawing2:

Aim:

To Create a layout of the Kitchen plan (Both Above Counter plan and Below Counter plan) and to take a plot.

Introduction:

The given drawings are coverted into PDF and printed for making the Drawing sheets Using the template TutorialmArch.dwt

Procedure:

The Drawings after created in Autocad are converted into PDF using the following procedure:

• A layout is created for the given drawing as per requirement.
• The layout is renamed as per the Drawing name or any other name Convenient.
• New views are created using the VIEW MANAGER in the Drawing for easy viewing of the reqiured PLAN or ELEVATION or SECTION.
• Later the same Drawing is taken as the viewport for making views as per the requirement.
• Firstly the Paper of required dimension is taken.
• It is obtained from PAGE SET UP MANAGER.
• Here it is used to Create New setup or Modify the Existing setup
• Later the paper view can be adjusted in Paperspace by Zooming in or Out.
• Command : PS or PSPACE
• The Plan or section or Elevation is taken in Modelspace and adjusted as per the scale.
• Command : MS or MSPACE
• Generally to represent different drawings in a single sheet,the sheet is made as tiles in the PAPERSPACE.
• Command : MV or 
• UsING the MV command to create the viewport.
• The Drawing is adjusted in the Tiles of the Paperspace using the following command
• Command : PAN
• Templates drawings can also be inserted while plotting.
• Some template drawings which are made as Blocks are also inserted.

For Plotting:

• After finishing all the adjustment in both Paper and Modelspace the Drawing is converted to pdf.
• For printing the Drawing the settings are checked and made ready to print.
• Settings include in the PAGE SETUP are:
• Paper size, Plot Area, Plot style Table, Plot Options , Drawing Orientation ,Plot Scale etc..
• The PDF Drawing is saved in the Folder and named conveniently.
• Finally the Drawing is Printed.

 RESULT:

result are attached with the file

Drawing3:

Aim:

To Create a layout of the Industrial Building and the Section of the Building and to take a plot.

Introduction:

The given drawings are coverted into PDF and printed for making the Drawing sheets Using the template TutorialmArch.dwt

Procedure:

The Drawings after created in Autocad are converted into PDF using the following procedure:

• A layout is created for the given drawing as per requirement.
• The layout is renamed as per the Drawing name or any other name Convenient.
• New views are created using the VIEW MANAGER in the Drawing for easy viewing of the reqiured PLAN or ELEVATION or SECTION.
• Later the same Drawing is taken as the viewport for making views as per the requirement.
• Firstly the Paper of required dimension is taken.
• It is obtained from PAGE SET UP MANAGER.
• Here it is used to Create New setup or Modify the Existing setup
• Later the paper view can be adjusted in Paperspace by Zooming in or Out.
• Command : PS or PSPACE
• The Plan or section or Elevation is taken in Modelspace and adjusted as per the scale.
• Command : MS or MSPACE
• Generally to represent different drawings in a single sheet,the sheet is made as tiles in the PAPERSPACE.
• Command : MV or 
• UsING the MV command to create the viewport.
• The Drawing is adjusted in the Tiles of the Paperspace using the following command
• Command : PAN
• Templates drawings can also be inserted while plotting.
• Some template drawings which are made as Blocks are also inserted.

For Plotting:

• After finishing all the adjustment in both Paper and Modelspace the Drawing is converted to pdf.
• For printing the Drawing the settings are checked and made ready to print.
• Settings include in the PAGE SETUP are:
• Paper size, Plot Area, Plot style Table, Plot Options , Drawing Orientation ,Plot Scale etc..
• The PDF Drawing is saved in the Folder and named conveniently.
• Finally the Drawing is Printed.

Result: