Sketch a G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code

1. Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows: Building floors G + 6 + R Plan dimension B = 25m ,  L = 16m Storey Height h = 3.5m Soil  Hard soil Use Residential Purpose Safe Bearing Capacity 180 kN/m2 Maximum slab thickness…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures Static analysis Dynamic analysis Static Loads are the loads which varies very slowly (the acceleration of load is very very less than the natural frequency of the structure) Dynamic Loads are the loads which changes with time…

Question-1. (a) What is the mode of failure or damage of the beams in the figure above? Are the damages repairable?Elaborate Answer Observation: Concrete crushed and the reinforcement is exposed. Cracks are large and concrete spalled out. Reinforcements are visible through the crack. Cracks are found at support bottom.…

1. Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class   Aim:To export the revit architecture and structure model to navisworks cache file. Introduction: Navisworks…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.   Aim:To create a set of sinusoidal points, a curve and a surface out of the curve using dynamo. Procedure: Step.1 Initially, open the architecture template of Revit software and go to manage tab. In manage…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School   Aim : To select a structure for modelling in the Revit software. Procedure :…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project.   Ans: AIM: To Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project.   Tools used:- Architectural template Grid…

1.Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ? Building codes is the most important concerns, including public health and safety, and environmental protection. Building codes are used, when we are constructing a building ----> It gives the standard codes, that prevents…

1.  Aim:To create the ceiling above the walls at the first floor level.   Procedure: Initially open the week 3 assignment from the revit software. For this initially go to plan view.   Step 1.Stair case design  Next we have to create the Stair case connected the First Floor. For this go  to Stair…

1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created from…

{1}.What is BIM? Summarize the features of BIM and the benefits of using BIM over 2D CAD tools.     Building Information Modelling  Building information modeling is a process supported by various tools, technologies and contracts involving the generation and management of digital representations of physical…

1. From the file menu, create a new project (Structural / Architectural / Construction template) and name the project appropriately. Aim: To Create a new project and name the project appropriately Introduction: Revit is an Autodesk product and is a building information modeling software for architects,landscape architects,…

Project 2 :- Creating a 3D rendered model for a Residential Building in AutoCad AIM: To create the 3D rendered model for a Residential building in AutoCad. Introduction :- 3D CAD, or three-dimensional computer-aided design, is a technology for design and technical documentation, which replaces manual drafting with an automated…

1. Aim :- To Create a 3D Isometric View of the building with plan and elevation given.     Procedure :- Click on AutoCAD application and open this application Type QNEW in command bar and enter Select default setting as Imperial In default setting click on use a wizard and in that advance setting and set unit as…

1. Aim: To draw the 3D wireframe model as shown in the figure. Introduction: The 3Dwireframe model given is a furniture equipment in the house. The 3d wireframe model is drawn in different coordinate systems such as rectangular coordinate system, spherical coordinate system, relative coordinate system and cylindrical coordinate…

Aim: To create layout of the Plan and Section A of the project in Challenge 7 as shown in the figure above, in AutoCAD. Introduction: The layout is created in AutoCAD using the template Tutorial-mArch.dwt in a scale 1:50 that given in the Figure. The procedure is explained in detail with diagrams of each step and the final…

1.PROBLEM 1 Aim :- To create the kitchen layout and to provide the hatch. Introduction :- The general commands used for drawing the building is as follows : 1. Line 2. Polygon 3. Rectangle 4. Circle 5. Erase 6. Copy 7. Trim 8. Mirror 9. Offset 10. Extend 11. Array 12. Move 13. Rotate 14. Dimension 15. Text 16. FilletEtc.…

Aim: To create templates and convert as shown in the figure using AutoCAD. Procedure: STEP:-1 In the command prompt type UNITS and press enter. Select the required units as desimal and select the required insertion scale. Select layer settings from ribbon tab. From the layer settings tab select create layer option. Enter…

Aim :- To Design and Draft a layout of a Residential Building having plot size of 60' X 20' ( 18.3m X 6m ), facing East-direction using AutoCAD.   Section 1 :- Architectural Drawing Site Plan Layout Ground Floor Plan First Floor Plan Elevation Section View Section 2:- Structural Drawing :- Column Layout Plan Beam…

[Q]:Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project.  Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required.   Aim: To draw the floor plans and sections using the…

Introduction AutoCAD's dimensioning tools can automatically measure distances and place dimensions on your drawing. You have to just select the objects, appropriate dimensions will be added by the AutoCAD. Dimension tools can be acccessed from the Dimensions panel on the Annotate tab of the ribbon. AutoCAD divides dimension…

Q1: Create a column schedule as shown in the figure. Note: Create a column schedule with the help of lines. Also, insert text with the help of Dtext command or Single Line text. Hint: Use font name: romans.shx; Height: 8”, Justify: Left Aim: To create column schedule as shown in the figure using AutoCAD Procedure:…

Aim: This challenge aims to show the application of the AutoCAD software in the Civil Engineering industry. In this challenge, the AutoCAD software is applied in the sketching of a Residence Layout, Seating Plan, and Toilet Rooms. With the combination of the different AutoCAD tools, the sketch can be provided easier and…

AIM:Drafting of various geometry using Chamfer,Fillet tool in Auto CAD.     INTRODUCTION: Auto CAD consists of a number of drawing and modification tools. Among the modification tools are Chamfer, Fille Offset Object snap Rotate Copy Move Mirror Trim Extend Join Chamfer: A chamfer is an angled line that meets…

AIM : To create Cross-Sectional View and Isometric View of some Engineering Drawing using AutoCAD. Introduction: (a)Cross-Section view : It is a typical or representative sample of a larger group. It is a surface or shape exposed by making a straight cut through something, especially at right angles to an axis. In geometry,…

Q.Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool.Please read the drawings and find out the missing dimensions before working on the sketches. AIM: Create the geometries from P1 to P2 using…

Aim: To sketch a G+1 floor residential plan according to Vastu Shastra and to list down the names of structural drawings required to be provided to the site of construction. Assume the size of structural elements ( column,beam ,slab etc.) and accordingly calculate the individual corresponding loads from the members according…

           Concrete Mix Design for M35 grade Concrete With Fly ash             AIM: To Calculate the Concrete Mix Design for M35 grade concrete with fly ash.   OBJECTIVE: Produce a cost effective fly ash based concrete. To achieve the Tatget mean strength…