Creation of geometries by Coordinate system methods using AutoCad

Challenge 6 – ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. sol- Open e tabs 2) select…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

1}The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Ans: Symmertry: It is observed that the distribution of mass, stiffness…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class   Aim: Using the Architecture/ Structure Project file developed and exporting the Revit architecture and…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve.   Introduction: The workspace is the place where designers develop visual programs but it is also the place where any elaborate geometry is previewed. Conceptual mass of a building contains different types of…

    1.1) Use the shortcut keys in Revit discussed in class to complete the following tasks and list them below Aim:  To list the shortcut keys for the following:  a. Using 3D model create a section box b. To create similar doors and windows in a floor plan layout c. To reduce the thickness…

1) What are HVAC systems? Why are they essential in the modeling of buildings. ans-An HVAC (heating ventilation air conditioning) system is integrated into a building to provide comfort for the residents. It allows for creating a comfortable environment by controlling the temperature of a room through heating and cooling.…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School   Ans - Multi-Unit residential building. 2) Assume reasonable assumptions for geographic…

1) What is the mode of failure or damage of the beams in the figure above? Would you characterize the case as damage or as afailure? Are the damages repairable? Elaborate.   This crack will be formed due to the flexural failure of a beam. The flexural strength, known as modulus  strength, or fracture strength,…

1) Open an architectural template. Using the Manage tab set project base point and project shared coordinates for the project  Aim: to set project base point and project shared coordinates for the project.Procedure:To create project shared coordinates:Open architectural tab.Open Manage tab.Click on project coordinates…

1) Why are building codes or standards essential for the modeling/ efficiency of drawings in Revit ?   ans-A building code (also building control or building regulations) is a set of rules that specify the standards forconstructed objects such as buildings and nonbuilding structures.Building codes specify minimum…

  1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. Aim- To create  To create ceiling on revitstep 1 Open architectural tabstep 2 Select Ceiling optionstep 3 Sketch Ceiling according to the given…

  1) Use the project file created from Week 2. Use it for this assignment. Based on your layout from week 2, using floor tool under architecture tab and select the floor with appropriate material and thickness using the property browser create a layout in the Ground floor Level. Align the floor plan with grids created…

1) What is BIM? Summarize the features of BIM and benefits of using BIM over 2D CAD tools.   Ans -1) The BIM- BUILDING INFORMATION MODELLING is the software to design the building in each and every prespective including all the basic                   and advance requirements…

Introduction to REVIT concepts. Revit is the BIM software and building information modeling software which is used in building information modelling of mechnical electrical Plumbing   setup design in one platform for in 3 d view .    Aim- From the file menu, create a new project (Structural / Architectural…

AIM: To create a 3D rendered model for a Residential Building in AutoCAD   Commands Used in this challenge Line Rectangle Trim Move Copy Explode Circle Dimlinear Dimcontinue Boundary 3Dorbit 3D rotate Extrude Region UCS Camera Block Render RR Sweep Create Light   Open AutoCAD In Startup settings start from scratch…

AIM-  Create a 3D Isometric View of the building with plan and elevation given.   PROCEDURE - Commands Used in this challengeLineRectangleTrimMoveCopyExplodeCircleDimlinearDimcontinueBoundary3Dorbit3D rotateExtrudeRegionUCSCameraBlockRender RRSweepCreate Light Step 1: Creating LayersOpen Layer properties and…

aim- Residence Plan: Sketch the layout of a residence as shown in the Figure 1. Consider all dimensions as reference to sketch the unit plan. Also the text in the layout are only for reference. Assume the missing dimensions. Also, refer the schedule for size of the doors.   Procedure - command -Line draw the the according…

AIM-Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings a. Plot Size: 31’x33’  b. Orientation- Facing East Creating my own house layout and section .   procedure  ommand: _rectangSpecify first corner point or [Chamfer/Elevation/Fillet/Thickness/Width]:Specify…

AIM-Create the Plan and Sections as shown in the Figures. Use proper dimension techniques and dimension styles to document the project. Assume the sizes of the doors and windows as per construction standards. Refer to sections for stair details if required. PROCEDURE- Click REC' Rectangle command to draw the outer of the…

Aim- Create a 3D Furniture element as shown in the Figure. Assume dimensions which are missing.   Procedure- Select object or bounded area:Specify extrusion height or [Multiple]:Specify extrusion height or [Multiple]:4"1 extrusion(s) createdSelect object or bounded area:Click a face, curve, or inside a bounded areaSelect…

 AIM - Create a layout of the Plan and Section A of the project in Challenges 7, using the template Tutorial-mArch.dwt in a scale as given in the Figure. Use the MV command to create the viewport of the size as shown in Figure. Also, use ATTEDIT command to edit the information in the title block. Use A1 size for the…

AIM- Create the layouts of the Kitchen and provide hatches pattern as shown. Also, use blocks wherever required. Provide appropriate dimensions in the plan. Assume the size of doors, appliances and others as per the standards. PROCEDURE - )open autocad select the template  2)select text command -open annote tab chose…

Aim-Create the templates as shown in Figures. Take the size of the title block as per industry standards or you can assume it as per the size of the paper. Use text and attributes wherever required. After creating the title block you need to save it as a block with names: Custom1_titleblock and Custom2_titleblock, respectively.…

AIM -Creating a wadrobe detailed drawings ,floor plan , kitchen layout , column details using autocad.     Step by step drawings :- Fig 1   1)open autocad select the template  2)select text command -open annote tab chose style and size of the text. 3)create table and select text command and start accordingly…

Procedure 1)open autocad select the template  2)select text command -open annote tab chose style and size of the text. 3)create table and select text command and start accordingly as per question example  4)In fig no-02 as per question no -2 select table use table command in command box and coose the table as…

AIM-Drafting of various geometries using Chamfer, Fillet tool in AutoCad. fig 1  1}open units and set the unit to deceimal digit  2}select line tool and start drawing line tool and input the value mensioned in the fig . 3}Drop the line using and turn on the polar co-orinate option . 4}Draw the ref. line to construct…

Aim-Creating a Floor plan, Footing detail and Isometric view using AutoCad. PROCEDURE:     1. Type „U‟ ◄┘ (enter) and set up the units in meters. 2. Type „L‟ ◄┘ give the dimensions for line as 5.0 ◄┘ and indicate the direction of line if ortho is ON 3. Proceed the above procedure for all the walls.…

Create the geometries from P1 to P2 using all the coordinates system methods. You need to use the Line tool to create the geometries. Where required you need to use the circle tool.Please read the drawings and find out the missing dimensions before working on the sketches. Note: Use the Imperial Template and the Decimal…

1)The names of the structural drawings required to be provided to the site for construction. a.Foundation detailing  b.Layout plan c.Floor Plan d.Plinth Beam plan e.column and beam Rcc Detailing  f.Slab detailing  g.Elevation 3D and Detailing  h.Doors and window Detailing.   1)The sizes of the…

1)ans- Grade designation : M35 Design mix b) Type of cement:53 grade Ordinary Portland Cement conforming IS 12269 c) Maximum nominal size of coarse aggregate : 20 mm d) Minimum amount of cement : 400 kg/m'as IS 2911-Part 1/Sec 2 & IRC 78-2014. e) Maximum water-cement ratio :0.40 as per IRC 78 -2014, f) Workability…