Project - Data Handling and Interpolation

Objective: The objective of the project is to route the wiring harness on given Bugatti V16 Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best practices should be demonstrated in design. All the necessary details like clearance,…

  -Below are the few references from the real world which were considered while designing the wiring harness for this project The wiring harness packaging rules and the industry best practices that have to be followed to complete this project are as follows:- Easy manufacturing, installation, removal, & maintenance…

 Flatten the harness assembly completed in “ week 4 challenge”. Place the flattened view on drawing sheet. Ensure bundles with protective coverings has different visuals on drawing view.   Routed the cable as per above reference in Electrical Harness installation work bench with proper lengths and…

  Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use the connectors provided. After completion of routing, Check the bundle Continuity. Add snap of result in submission     Add annotation to all connectors. Make an assumptions for annotations…

Q1. Route the following harness layout in Electrical workbench. Make assumption for harness bundle diameters. Use Following connectors as shown in layout diagram. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end)   Download connector…

  Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. For below P-clamp defined two entry points and one base plane  and its defined as supporting part in electrical part definition.   Q2. Download following Back…

Q1. Download following connectors & Connector clip cad data from given link & define it as Electrical Connector using Electrical Part design Workbench. Define all the necessary properties to Connectors & Clip.   Deutsch DT06 – 08SA ( https://www.te.com/usa-en/product-DT06-08SA.html) Tyco 174357-2…

      Question 1: Identify each of the major elements in the above automotive wiring diagram.  Answer: Major Elements in the above automotive wiring diagram are: Battery Starter Breaker Ignition Coil Distributor Generator Current & Voltage Regulator Foot Selector Switch Ammeter Fuse   Question…

objective - For a 10 cell series lithium ion battery model, simulate the thermal effects and compare life cycle performance at various temperatures, charge & discharge rates using MATLAB. Overview:  Lithium ion battery are mostly used in electric vehicles we must know its charge and discharge rates to operate…

1.Simulate the 3 test cases from harness dashboard and write a detailed report on the results 2.What is coulomb counting? Refer to the above model and explain how BMS implements coulomb counting for SOC estimation ?   Solution- Study 1:-Simulate the 3 test cases from harness dashboard and write a detailed report…

 AIM:-  Prepare a detailed battery pack of Cell: ANR26650M1-B, drawing along with its enclosure, & Battery pack capacity is 18kWh. State your assumptions.   Abstract:- In this project, we are going to calculate the all parameters which are required for the build EV battery pack. We are going to use the Cell: ANR26650M1-B…

AIM:- To understand different Battery chemistry.  OBJECTIVES:-                1)Prepare a table that includes materials & chemical reactions occurring at the anode and cathode of different types of lithium-ion cells.                2)Comparing…

  Description:As discussed in Lecture 11, Project 2 deals with the development of a forward energy-based fuel consumption model of a P1 hybrid vehicle. This model is based on the conventional vehicle model from Project 1. The main goal of this project is to understand the functionality of a P1 hybrid and be able to model…

Title:- Deals with the development of a forward energy-based fuel consumption model of a conventional vehicle. Aim:-  1] Build Simulink model using blocks and complete the vehicle model. 2] Writting scripts in MATLAB to load all the variables required for running the Simulink model. 3] Tabulate the fuel…

PROJECT: DC MOTOR SPEED CONTROL USING PID CONTORLLER Aim:  To design a Simulink model for the DC motor  shown in Figure 1. amd aslo by Using  the Proportional, Integral, and Derivative (PID) control design knowledge gained in the training to design, develop and test a controller to maintain a desired speed…

%  Project # Basic Matlab: clc close all clear all vi=xlsread('VI.xlsx','A2:A25');% Read the current values from VI.xls file vv=xlsread('VI.xlsx','B2:B25'); % Read the voltage values from VI.xls file xq=(-17.3:0.1:0.9); %intervals yq=interp1(vi,vv,xq);%interpolation for values of xq plot(vv,vi,'o',yq,xq,'-') %plote…