ANSWER:- Aim:- To design the beams in detail from the Etabs 2018. To provide details of longitudinal and shear reinforcement for the given two continuous beams. To calculate the value of maximum shear force in any one of the spans…
MUNNANGI MAHESWARA RAo
updated on 15 Dec 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by MUNNANGI MAHESWARA RAo (31)
Project 2_Design & Analysis of a Hostel building at Guwahati, Assam
AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie beam connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam…
23 Dec 2022 02:08 AM IST
Foundation Design using SAFE
AIM : To Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. INTRODUCTION : Foundation design is the creation of a construction plan for a building foundation. It is a highly…
21 Dec 2022 01:42 PM IST
Design of Shallow Foundation (Isolated Footings)
Aim: To manually calculate the spread footing dimensions and reinforcement details with respect to limit state design of soil and structure. Calculation of Gross soil pressure: Unfactored load = 2000/1.5 = 1333 kN Assume the thickness of footing (t) = 0.5 m Depth of footing as given in data (h) = 2 m, So soil surcharge…
20 Dec 2022 02:04 PM IST
Structural Modelling using Etabs 2018
Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and…
19 Dec 2022 01:27 PM IST
Analysis & Design of RCC shear walls in the model using ETABS
Aim: Detailing of shear wall Procedure: Step 1: The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2: The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below. From the obtained results, it can be seen that a boundary zone…
19 Dec 2022 02:32 AM IST
Reinforcement detailing of Columns from ETABS output
Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…
16 Dec 2022 05:43 AM IST
Reinforcement Detailing of Beams from ETABS output
ANSWER:- Aim:- To design the beams in detail from the Etabs 2018. To provide details of longitudinal and shear reinforcement for the given two continuous beams. To calculate the value of maximum shear force in any one of the spans…
15 Dec 2022 12:57 PM IST
Project 1_Comparative study of different storey buildings for Seismic forces
Aim: To model the buildings from A to K as per the details given below: To to carry out a comparative study of these buildings for seismic forces. Introduction: Every building has a number of natural frequencies at which it offers minimum resistance to shaking induced by external effects and internal effects. Each of these…
13 Dec 2022 03:39 AM IST
Modelling of 25 storey building with the specified properties using ETABS
AIM: ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. PROCEDURE: STEP1 Open E-Tabs…
12 Dec 2022 03:14 AM IST
Conceptual design of a building with columns and shear walls
1 Ans: As the structure is more restrained it will be more shrinking, expanding and cracking. There will be more floor shrinkage and expanding in structure A whereas there will be minimum cracks in structure B and C. The shear walls in the structure also decide whether the floor vibration is more or less in the structure…
10 Dec 2022 09:54 AM IST
Concept on positioning of Columns
1.Symmertry Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass,Stiffness is across the plan;it is observed that the distribution of mass, stiffness is across the plan.It is considered for one of the good Symmetrical aspects.This tends to reduce the horizontal displacements…
08 Dec 2022 04:18 PM IST
Understanding the concepts on Degrees of Freedom
Procedure: Step 1: For mode 1: We know that =(0.334)+(0.641)+(0.895)+(1.078)+(1.173) x m Similarly Mode 2 = m2 = 3.861m Mode 2 = m3 = 3.861m Mode 2 = m4 = 3.861m Mode 2 = m5 = 3.861m For the calculation of Ln: L1 = ( 0.334 0.641 0.895 1.078 1.173 ) x …
07 Dec 2022 12:57 PM IST
Structural dynamics
1. Differentiate Static analysis and Dynamic analysis by proper representing pictures STATIC ANALYSIS DYNAMIC ANALYSIS 1. Load is not variable with time and neglected due to slow applying of load. 1. Load is variable with time due to fast applying…
05 Dec 2022 11:34 AM IST
Identification of Cracks
1 : a) OBSERVATION FROM THE IMAGE :- As we can see that,Concrete crushed and the reinforcement is fully visible Concrete fall upto the rebars which may be a sign of rupture Beam top portion looks safe because of the flange advantage from slab The crack developes from bottom to top means…
03 Dec 2022 03:26 AM IST
Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork
) AIM: To Exporting the Revit architecture and structure model to Navisworks Cache file as discussed in the video. PROCEDURE: First of all we have to install the software form autodest website. Go to Autodesk website Search Naviswork export utility and download 2021 version Click run and extract it.…
01 Dec 2022 04:45 PM IST
Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo
Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code; while also creating an algorithm that consist of nodes. Using dynamo work can be carried out with enhanced…
01 Dec 2022 04:48 AM IST
Creating Architectural and Structural model with 3D rendering using REVIT
Q1) AIM: Select the type of structure you want to build from one of the three below: a. Multi-Unit Residential Apartment b. Office Buildings c. School. ANS) OFFICE BUILDING Q2) AIM : Assume reasonable assumptions for geographic…
22 Nov 2022 03:31 AM IST
3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT
1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level. AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level. INTRODUCTION:- The creation…
12 Nov 2022 05:47 AM IST
Project 2_Creating a 3D rendered model for a Residential Building in AutoCad
NTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is possible to create 3D objects, AutoCAD is built around a flat, sketch-based interface.…
18 Oct 2022 01:44 PM IST
Creating 3D Isometric view of various structural elements in AutoCAD
AIM:- To create a 3D isometric view of the given building with plan and elevation. INTRODUCTION:- An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing, compared to other types of 3D representation, is that the…
15 Oct 2022 12:20 PM IST
Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad
AIM : To create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW : The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two dimensional image…
13 Oct 2022 09:37 AM IST
Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad
1Aim: To Creating the layout of floor plan and section of challenge 7 project using Autocad Introduction: The main objective of this project is to understand about the viewports in Auto CAD. There are two types of viewports in AutoCAD. Model space viewports and layout space viewports.…
12 Oct 2022 06:54 AM IST
Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad
Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set zoom comand is also used Steps for drawing Below Counter Plan Open…
09 Oct 2022 12:23 PM IST
Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad
Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule. Commands used: Block. Insert. Attributes.…
08 Oct 2022 05:07 AM IST
Project 1 _Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings
1 ANS: …
05 Oct 2022 01:12 AM IST
Creating a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad
1 ANS: …
17 Sep 2022 06:47 AM IST
Drafting of various geometries using Chamfer, Fillet tool in AutoCad
ANS: Commands used are Line 'L' Copy 'CO' or 'CP' PolyLine 'PL' Trim 'TR' Offset 'O' Isometric View Text Dimension 'DIM' Dimstyle 'D' MATCHPROP 'MA' Move 'M' Mirror 'MI' Fillet 'F' Erase 'E' Rotate PTYPE POINT CIRCLE RECTANGLE Q.1) Decimal …
14 Sep 2022 05:37 AM IST
Creating a Floor plan, Footing detail and Isometric view using AutoCad
Aim: To draw cross section of wall over footing. …
12 Sep 2022 03:00 PM IST
Creation of geometries by Coordinate system methods using AutoCad
AIM: * To Create the geometries from P1 to P2 using all the coordinates system methods and P3 to P10 by any one coordinate system * To Draw the profile and the trusses using any coordinate system methods. The dimensions are there for reference. INTRODUCTION: Before going to the drawing, we should know…
09 Sep 2022 06:39 AM IST
Project on Concrete Mix Design for various grades of Concrete
1 ANS: To caluculate the concrete mix design fo M35 grade concrete with fly ash&M50 grade concrete without fly ash. OBJECTIVE: The objective of this project is to produce a mix desifn for M35 grade concrete conataining fly ash and M50 grade concrete. the mix will be prepared as per is METHOD: concrete …
19 Aug 2022 01:45 PM IST