Reinforcement detailing of Columns from ETABS output

  In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam Function…

1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. AIM: To model the isolated footing provided in week 11 challenge on SAFE PROCEDURE:- Open the SAFE software. Click on New model to create new model Now, New dialogue…

Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial load, also…

AIM:- To model and analyze the G+7 residential building from the given architectural drawings using ETABS PROCEDURE:- First we have to open the etabs software. Next click on the file option at the left side top corner and select the new model, as shown below. After selecting the new model the new tab opens,…

The etabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (show in the etabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length and shear reinforcing…

Reinforcement detailing of columns in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns,…

Challenge 7 – Detailed design of concrete buildings -1 Detail design of beams in Etabs.The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment Resisting Frame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3…

Aim: To model ten different buildings having different conditions as given. To compare and study the modelled different storey buildings for Seismic forces Introduction: The ten buildings named from A to K are given with conditions as mentioned below For all the buildings Structural Element Sizes  Beams : 300 ×…

Challenge 6 – ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes …

Question 1:The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Question 1: Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Solution: Symmetry In X-direction: It is symmetrical in x-direction,…

Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. The fundamental period of vibration (T1 = 2 seconds) and…

1. Differentiate Static analysis and Dynamic analysis with proper representing pictures STATIC ANALYSIS Load is not variable with time and neglected due to slow applying of load. Motion of the structure can be disregarded. There is no necessity to count Inertia and damping forces in the case of static analysis, but the…

What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate Question 1: a)   observations: Concrete is crushed and the reinforcement is exposed Concrete spalled beyond the reinforcement which may be a sign of rupture Beam top portion looks safe because of the flange…

1) Use the Architecture/ Structure Project file developed by you in Week 6 to 8. Export the Revit architecture and structure model to Navisworks Cache file following the export settings discussed in class Aim: To export the Revit architecture and structure model to Navisworks cache file Introduction: 1. Open the Revit,…

1) Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Aim : To create a set of sinusoidal points, a curve and surface out of the curve using dynamo Procedure: 1. Open Architectural template in Revit, go to manage tab 2. Choose the dynamo and open new file 3. Then first…

1) Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School Aim: To draw a office building as per the NBC guidelines in Revit by combining both Architectural…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Aim & Introduction: To model a ceiling above the walls at the first floor level using architecture toolbar Procedure: 1. Open the Revit drawing and go…

Aim & Intorduction: Creation of a 3D Isometric View of the building with given plan and elevation  Procedure: 1. First open a new drawing sheet and choose the units as engineering. 2. Draw the recgangle with given dimensions as shown 3. Offset the two sides with offset distance 9" using offset command 4.…

Aim & Intorduction: To create a 3 dimensional model of the residential building with a rendered view. 3d modelling is used. In layers layoff is used when needed to work easily. Extrude and solidedit commands are used to obtain the desired residential building. Use the commands 3drotate, union, subtract whever…

Aim & Introduction: Need to create given 3D furniture element. Dimesnsions are assumed whichever are missing. Solidedit command is used to obtain the given 3D furniture element. Dimlinear is used to insert dimensions, also UCS command is used to shift the axes wherever required for measuring the distances. Procedure:…

Aim & Introduction: A layout of the Plan and Section A of the project in Challenge 7 is created using the template Tutorial-mArch.dwt. The given scale 1:50 is used. Viewports are created using MV Command. ATTEDIT command is used to edit the information in the title block. A1 size of the layout is used and took…

Aim & Introduction: To draw kitchen layout of a building. Below counter plan and above counter plan both are drawn. Text and dimensions are inserted accordingly using comamnds. Procedure:  1. Open the AutoCAD drawing and give command units. Choose units as decimal and millimeters as shown. 2. Draw below…

Aim & Introduction : Creation of given templates. Templates were saved as Custom1_titleblock and Custom2_titleblock respectively using block command. Text and Tedit commands are used to insert the text. Procedure:  1. Create a rectangle using rectangle command. 2. Draw lines at respective distance using line…

Aim & Introduction: To design and Draft a layout of a residential building in AutoCAD. plot size is taken as 60’x20’(18.3m x6m)/ The facing of the building it taken to East side. Need to draft the architectural and structural drawing. Floor plan, elevation and two sections are drafted as part of Architectural drawing.…

Aim & Introduction: To create a plan and given sections. Sizes of windows and doors are assumed accordingly. Text and dimensions are given accordignly by using the commands. Dimension styles used to insert the dimensions as required. Procedure:  1. Opene the AutoCAD new file and choose units as decimal and…

Aim & Introduction: To draw elevation and details of a wardrobe. To use layers command to provide dimensions and text to the drawing. To draw front view, cascasde view and side view of the wardrobe. Every detail of wadrobe is drawn for clear understanding of drawing as mentioned. Procedure:  1. Open the AutoCAD drawing…

Aim: Need to create given column schedule in AutoCAD. Column schedule can be created using line command and with Dtext or Mtext command text is created. Procedure:  1. Set units to engineering by using units command 2. First we need to create columns as blocks to use them in column schedule 3. Draw a rectangle and…

Aim & Introduction:  To create a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCad. Demonstration of how residence layout, seating plam, toilet and ulitity room is drawn using AutoCad. More about layers, blocks and arrays are discussed. 1. Creation of a given residence layout using…

PLEASE REFER THE ATTACHMENT FOR WORD DOCUMENT