ROOF CRUSH ANALYSIS OF DODGE NEON BIW AS PER THE FMVSS 216A STANDARD

Values achieved from simulations: Result cast iron cast bronze cast steel Total deformation 30 mm 30 mm 30 mm equivalent elastic strain 3.3113e-03 3.6791e-03 1.5322e-03 equivalent stress 291.76 Mpa 290.25 Mpa 306.09 Mpa   kindly, suggest to me on what basis, should I come up with a suitable material. 

case 1: Max Total deformation=2.7492e-4 mm Max Equivalent stress=0.60542 Mpa case 2: Max Total deformation=2.9728e-4 mm Max Equivalent stress=0.5826 Mpa   1.From an analysis standpoint, i would select the model in case1, It provides less damage to the model, because the stress developed is slightly higher,deformation…

OBJECTIVE: The main aim of this project is to perform meshing on the given Cad model of the suspension system as per the quality criteria shown below and to provide necessary connections. QUALITY CRITERIA: For Surface Meshing of Tyre and Rim (Element type: Tria) :  S.No  Quality Criteria  Value  1 Target/Average…

OBJECTIVE: The main aim of this project is to mesh the half of the IP console model as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA:  S.No  Quality Criteria  Value  1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length  6 4 Aspect …

OBJECTIVE: The main aim of this project is to perform the basic morphing technique for a Hand rest plastic component and a sheet metal component. PROCEDURE: Hand rest plastic component: Imported the given .stp file in the ANSA work page. Checked for the orientation i,e. the upper part of the model should be in gray color…

OBJECTIVE: The main aim of this project is, To mesh the cross-car beam parts as per the quality criteria shown below. To provide necessary connections. To assign thickness. QUALITY CRITERIA: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  3 3 Maximum Length …

OBJECTIVE: The main aim of this project is to mesh the Intake manifold of an engine using tetra elements as per the quality criteria shown below. QUALITY CRITERIA: S.No  Quality Criteria  Value  1 Target/Average length   3 2 Minimum Length  1 3 Maximum Length  5 4 Tetcolapse  0.2…

OBJECTIVE: The main aim of this project is to connect the FE model of the rear door of a car in Nastran deck for NVH domain. PRE-REQUISITES: NVH domain study about the natural frequency of the body at which it vibrates, so for the basic simulation mechanisms in the system are not need to be defined (case specific). Basically,…

OBJECTIVE: The main aim of this project is to mesh the Switch panel of a car and a sheet metal component as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA:  S.No  Quality Criteria  Value  1 Target/Average length   4 2 Minimum Length  2 3 Maximum Length …

OBJECTIVE: The main aim of this project is to mesh the Rearview mirror using tetra elements as per the quality criteria shown below. QUALITY CRITERIA: S.No  Quality Criteria  Value  1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  2 4 Tetcolapse  0.2 PROCEDURE:…

OBJECTIVE: The main aim of this project is to mesh the Bottle cap as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: 1 Target/Average length   1 2 Minimum Length  0.5 3 Maximum Length  3 4 Aspect  3 5 Warpage 15 6 Skewness 45 7 Jacobian  0.7 8 Minimum Quad Angle …

OBJECTIVE: The main aim of this project is to mesh the hood of a car as per the quality criteria shown below and to assign thickness. QUALITY CRITERIA: S.No  Quality Criteria  Value  1 Target/Average length   5 2 Minimum Length  2 3 Maximum Length  7 4 Aspect  3 5 Warpage 15 6 Skewness…

OBJECTIVE: The main of this project is to perform the roof crush analysis of Dodge Neon BIW as per the requirements and procedures in FMVSS-216a standard published in 2009. FMVSS-216a STANDARD: FMVSS 216, Roof Crush Resistance, establishes strength requirements for the passenger compartment roof of passenger cars, multipurpose…

OBJECTIVE: The main aim of this project is to perform a side crash of neon's BIW model using preprocessors like Hypermesh, Hypercrash, and Radioss solver. PROCESS: 1. The consistent unit system in this project is Kg mm ms KN. 2. Created an appropriate contact interface type-7 self-impact with the recommended parameters…

OBJECTIVE: The main aim of this project is to perform a frontal crash of neon's BIW model using preprocessors like Hypermesh, Hypercrash, and Radioss solver. PROCESS: 1. The consistent unit system in this project is Kg mm ms KN. 2. Created an appropriate contact interface type-7 self impact with the recommended parameters…

objective: the main objective is to mesh the given component according to the quality criteria given in the question. Element quality criteria : S.N Quality Criteria  Value  1 Target Element Length  5 2 Aspect Ratio  3 3 Skewness 45 4 Warping 30 5 Taper      0.5 6 Min. Length 3mm 7 Max.…

1.Objective (tet mesh): The main objective of this project is to create a 3D tetra mesh for the component (housing) as per the quality criteria given below. Quality criteria: Elements sizes: Min- 2mm, Target- 5mm, Max- 7mm  Tet collapse: 0.15 Procedure: Imported the file from the question and performed the 2d tria…

1.Objective: The main objective is to mesh the backdoor component according to the quality criteria given below. Target Element size - 5mm S.N Quality Criteria  Value  1 Aspect Ratio  5 2 Skewness 45 3 Warping 15 4 Taper      0.5 5 Min. Length 4mm 6 Max. Length 7mm 7 Min angle Quad 45 8 Max…

OBJECTIVE: The main aim of this project is to study and compare the contact interface type 2, type 7, and type 11. To study how the notch influence the simulation in the crush tube model. To mesh the bumper assembly model with a 6mm element size. BUMPER MESHING: procedure followed: imported the given model (.hm) file…

OBJECTIVE: The main aim of this project is to analyze the different material card cases given and to derive the case which represents the on-field scenario. DESCRIPTION: case1: imported the given failure_johnson_0.rad file in the hypermesh GUI. simulation is done with the material card of law2_PLAST_JOHNS and failure johnson…

OBJECTIVE: The objective of this project is used to create a model of different parts of the Chopper using Solidworks. To assemble the different parts modeled for the chopper. To create a Photorealistic model of the chopper and Render the model using Solidworks visualize. PART MODELING: Part Modeling you…

objective : The main aim of this project is to connect the different components of a frame assembly using different connectors in hypermesh. procedure: imported the assembly file in hypermesh software. since the components are surface checked for geometry cleanup. splitted the surfaces to attain fine mesh. generated 2d…

OBJECTIVE: The main aim of this project is to mesh the side door of the car as per the quality criteria shown below. To assign thickness for the mesh elements. QUALITY CRITERIA: PROCEDURE: selected the radioss user profile for durability analysis. imported the model (.hm) file into the hypermesh. checked for any geometrical…

OBJECTIVE: The main aim of this project is to mesh the back wheel panel of the car as per the quality criteria shown below. To assign thickness for the mesh elements. QUALITY CRITERIA: PROCEDURE: Selected the radioss user profile for durability analysis (say). Imported the back wheel panel model (.hm) file into the hypermesh…

MODELING AND RENDERING OF ROYAL ENFIELD CLASSIC 350 USING SOLIDWORKSOBJECTIVE: 1.The main objective of this project is used to create a model of different parts of the royal Enfield classic 350 using Solid works. 2.To assemble the different parts modeled for the classic 350. 3.To create a photo-realistic view of the…

SUNSEEKER PREDATOR YACHT OBJECTIVE: The main aim of this project is to create a surface model of different yacht parts. To assemble the parts modeled using the SolidWorks 2018 software. To create a photorealistic model of the yacht and render the model using the SolidWorks visualize software.   PART MODELLING:…