To calculate wind load for industrial steel structures and to apply it by using TSD

AIM : TO Analyze and Design the RC office building as per IS standard code in TEKLA STRUCTURAL DESIGNER.   PROCEDURE : First we have to mark the column and beam positions in tthe given plan. Open tekla softwre and create the construction levels with the given data of elevations. then create grids for the model based…

Q1. Aim: To Generate report for the steel building design from challenges 1 – 6 along with the loading summary. Procedure: First pen the previous Tekla model. Next go to the report option under the Ribbon tab then select model report. After that choose the load cases and combinations to obtain report. Click…

AIM : To Design the slab and foundation of the model. Outline the thought process for designing of the elements (column, beam, slab and foundations). Slab Design: Procedure :  first open the previouis model do validate and if the errors will be found clear the errors. then go to the ground floor and unselect…

Aim: To design the RC columns and beams based on the analysis. Procedure: Designing Columns: Open the previous Tekla file. Now right click the on member to be designed, and then select interactive design and select static. Select Static from the Interactive Design, after that, a dialogue box appears. This dialogue…

  AIM: Generate seismic loading based IS codal provisions and zone II. Any other data you can assume and input accordingly.Run the analysis. Summarize your understanding of the analysis results Procedure: first open the previous mdel go to load tab and select the sesmic wizard option. enter the data according to thatreqired…

Q.1 Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab thickness as per the design Brick wall load Roofing load Load calculations: Dead load = 1.2kN/m^2 Finishes = 500mm x 24kN/m^3 = 1.2 kN/m^2 Brick wall load = 0.15 x 20x 5.2 = 15.6 kN/m^2 (Ground to intermediate…

Q1. Setup model for RC building design and based on following parameters for cover MEMBERS IN CONTACT WITH GROUND ABOVE GROUND Column 50mm 40mm Beam 30mm 25mm Slab 30mm 25mm Pilecap 75mm   Foundation 50mm Open the tekla software create new template. open the settings under the home tab. then set the data as given…

AIM: To analyze and design a steel building to 10T CRANE as per IS standard code using TEKLA STRUCTURAL DESIGNER. INTRODUCTION: Tekla Structural Designer is a software tool that integrated model-based 3D tool for analysis and design of both concrete and steel members. In this tool we can do modeling, analysis…

AIM :To Analysis and Design of Steel Structures using TSD 1.Summarize your study for the bending moment, shear force and deflection diagrams for the elements of the model OPEN THE MODEL then go to the analyze tab then select analyze settings. after that 1st order nonlinear to be ok. then check the all concrete factors…

1.Generate manual wind loading in the design report based IS code as per the following input Basic wind speed = 39m/s Terrain category 2 AIM: To calculate wind load for industrial steel structures and to apply it by using TSD   2.Based on the above calculation apply the loadings on the model Open the model goto the…

To calculate dead and live load for industrial steel structures and to apply them using TSD 1.Calculate dead load in design report based on IS code and apply dead load on the model Finishes of 50mm Slab as per design Brickwall 150mm thickness Roofing load based on purlin size Ceiling loading 0f 0.3KN per sq m AIM: TO Calculate…

 AIM : To model beams and bracings for industrial steel structures using TSD 1.Create beam properties for First floor and model the beams FOLLOW THE SAME PROCEDURE TO CREATE BEAMS IN THE FIRST FLOOR AS PER THE PREVIOUS CHALLENGE GROUND FLOOR. Create the primary beams and secundary beams . 2. Create rafter beam…

AIM: To model columns for industrial steel structure using TSD. Create column properties for different types of pedestal members and model in the grids created as per the assignment 1 open the new file and create the grids and levels as per the assignment 1 then go to the management property sets . click on new and add…

1)Summarize the user interface in TSD with the for the following items: -  Project Workspace – How to access and usage  First open the tekla structures sofware GO TO FILE TAB click on the new option it will automatically create a work space for the new project.  Scene Content – Demonstrate the…

Aim: Design & Analysis of a Hostel building at Guwahati, Assam. Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate with the grid-like…

Aim : Foundation Design using SAFE . Introduction : SAPFire® Analysis Engine (Slab Analysis by the Finite Element Method) CSI solvers have been tried and tested by the industry for over 45 years. The SAPFire Analysis Engine can support multiple 64-bit solvers for analysis optimization and can perform both…

AIM: To Design of Shallow Foundation (Isolated Footings). Introduction: the challenge gives knowledge on the desing of footings.this totally a manual design for practice purpose. Footings which are provided under each column independently are called as Isolated footings. They are usually square, rectangular or circular…

Aim : Structural Modelling using Etabs from the Architectural drawing.   Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate with…

Aim: Analysis & Design of RCC shear walls in the model using ETABS. Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate with the…

Aim: Reinforcement detailing of Columns from ETABS output. Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate with the grid-like geometry…

Aim: Reinforcement Detailing of Beams from ETABS output Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate with the grid-like geometry…

Aim : Comparative study of different storey buildings on different conditions for Seismic forces.   Introduction : ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques,…

Aim : Modelling of 25 storey building with the specified properties using ETABS Introduction :ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and solution techniques, all coordinate…

Question 1)The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account the restraint…

Question 1)Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. symmetry: the above given framing plan was  very good at symmetry…

  Question 1: A five storey structure with 5 translational DOF is shown here. Each storey has mass ‘m’. The eigenvalue problem has been solved and the 5 periods of vibration Tn and their corresponding mode shapes, φn has been derived. ANSWER : RESULTS:- Ln , Mn and Γn for…

 Question 1) Differentiate Static analysis and Dynamic analysis with proper representing pictures (30 marks) Static analysis : it is an analysis of a structure considering the static loads like dead and live ,which are does not vary with respect of time. in this analysis we did not consider sudden applied . In…

Identification of Cracks Question 1 : What is the mode of failure or damage of the beams in the figure above? Are the damages repairable? Elaborate a)  in this picture the mode of failure is dispaching of concrete from the rebars and production of cracks from bottom to the top of beam due to the high…

AIM : Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork Introduction: Revit is a one of Building Information Modelling software for architects, landscape architects, structural engineeers, mechanical, electrical and plummbing(MEP) engineers, designers and contractors. Revit supports a multidiscipline…

AIM : Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric stadium using Dynamo Introduction: Revit is a one of Building Information Modelling software for architects, landscape architects, structural engineeers, mechanical, electrical and plummbing(MEP) engineers, designers and contractors.…

AIM : Creating Architectural and Structural model with 3D rendering using REVIT Introduction: Revit is a one of Building Information Modelling software for architects, landscape architects, structural engineeers, mechanical, electrical and plummbing(MEP) engineers, designers and contractors. Revit supports a multidiscipline…

 AIM : 3D Creation of Celing, Roof, Architectural plan, Structural plan, Sectional view, Elevation view and Camera specific view for a house plan using REVIT Introduction: Revit is a one of Building Information Modelling software for architects, landscape architects, structural engineeers, mechanical, electrical…

AIM : To Creating a 3D rendered model for a Residential Building in AutoCad INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

AIM : To Creating 3D Isometric view of various structural elements in AutoCAD. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

  AIM : To Creating various 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include:…

  AIM : To Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

AIM : To Creating Kitchen layout, Hatching of Architectural elements and sectional view of an Industrial Building in AutoCad. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: -…

AIM : To Creating Bar Bending schedule, Different Door types, and Creation of standard drawing templates using AutoCad INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction…

AIM : To Design and Draft a layout of a residential building with the given details & to develop the architectural drawing ,structural drawings. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These…

AIM : To  Create the Plan and Sections as shown in the Figures. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

AIM : To Creating a Wardrobe detailed drawing, Floor Plan, Kitchen Layout and Column Detail using AutoCad. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction…

  AIM : To Creation of Column Schedule and Drawing Template  by using AutoCad INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

AIM: To Create a Residence Layout, Seating plan, Toilet and Utility room plan using AutoCAD. INTRODUCTION: AutoCAD offers various tools to perform different tasks. The various tools which are used for drafting in this project are briefly described here. These draw tools include: - line,Construction line,rectangle,polygon,polyline,circle,elepse…

AIM:  To DRAFT THE VARIOUS GEOMETRIES USING CHAMFER, FILLET TOOLS IN AUTOCAD.  INTRODUCTION: AutoCAD consists of a number of drawing and modification tools. Among the modification tools are the Chamfer, Fillet, Offset, Object snap, Rotate, Copy, Move, Mirror, Trim, Extend and Join. here we use some…

Aim: To create a floor plan, footing detail and isometric view using AutoCAD tools. Introduction: AutoCAD software consist of different tools that are essential for drawing a floor plan, footing detail or an isometric view. Some of them includes rectangle, polygon, polyline,line etc .  There are various modification…

  Aim : To Create the geometries from P1 to P10 using all the coordinates system methods with line tool and circle tool where it required and read the drawings and finding out the missing dimensions. Introduction : The program begains in 1977 & which is released in 1979 that named as interact cad .the first…

Aim : To Sketch a G+1 floor residential plan, according to Vaastu Shastra, and list down the names of the structural drawings required to be provided to the site for construction.calculation of the individual corresponding loads from the members as per IS code. Introduction to Vaastu Shastra : Vastu Shastra is the…

1.Calculate the Concrete Mix Design for M35 grade concrete with fly ash ? Given data (assumed) : a.grade                                   = M35 b.type of cement                   …