Week 1 Challenge

All the answers in given pdf in below...

Question In this project, participants will get to experience the entire design process from modelling, analysis, design, and preparation of construction drawings. The architectural drawings of a G+3 RCC building is provided. The following information on the building is to be used: Location – Guwahati, Assam Function…

Questions Foundation Design using SAFE 1. Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. 2. A column of size 600x600 carrying an unfactored gravity load (DL+LL) of 1175 KN is to be supported on pile cap, which ultimately…

Question Design a square footing for a column size of 400x400. The compression axial load for the load combination of (1.5 DL + 1.5 LL) is 2000 KN. The safe soil bearing capacity is 150 KN/m2 at a depth of 2 metres below E.G.L. Participants are free to go for either a tapered or stepped footing. Besides the total axial…

Question The architectural drawings for a G+7 residential building in zone 5 has been provided. The floor plan is the same for all 7 floor levels. Possible column positions have also been provided.Conceptualize a framing plan layout and then model the building in Etabs. The following architectural drawings have been provided:…

Question The tabs file for a G+6 building is provided. Run the analysis and design the RCC shear walls (shown in the tabs model). The following challenge deals specifically with the shear wall of size 300x1500 at grid A-11 in the structural model. Extract values of longitudinal steel ratio, boundary element length,…

Question The ETABS file for a G+4 building is provided. Run the analysis and design of the RCC Moment Resisting Frame. The following challenge deals specifically with two columns at the following grid intersections. 3A 3B Provide details of longitudinal reinforcement for the two columns, from foundation to terrace level.…

Question Detail design of beams in Etabs 2018. The ETABS file for a G+4 building is provided. Run the analysis and design the RCC Moment ResistingFrame. The following challenge deals specifically with two continuous beams in the 1st floor.         1) 3 span continuous beam along grid A        2) 7 span continuous beam…

Question Factors influencing the dynamic characteristics of a building Factors influencing the Natural Period of a building Factors influencing the Mode shape of oscillations. Structural Element Sizes  Beams : 300x400mm Columns : 400x400mm Slab : 150mm thick Material Properties Grade of concrete : M30 Grade of steel…

Question Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. Structural Element Sizes: Beams : 300 × 400 mm Columns : 800 × 800 mm Slab:…

Question - 1The building shown, 20 × 35 m in plan, has columns on a 5 × 5 m grid and shear walls (with dimensions shown in m, 250 mm in thickness) in three alternative arrangements, (a), (b), (c), all with the same total cross-sectional area of the shear walls. Compare the three alternatives, taking into account…

Question-1 Comment on the layout of the framing plan concerning earthquake resistance in the two horizontal directions X or Y (dots are columns, lines depict beams). Look into aspects of symmetry, redundancy and bi-directional stiffness and ductility. Answer: In this, the layout of the framing plan is Symmetric. A symmetrical…

Question 1. Differentiate Static analysis and Dynamic analysis with proper representing pictures 2. Explain the following with relevant force-displacement graph  Elastic behavior Inelastic behavior Plastic behavior Non-linear Inelastic behavior 3. Explain Mass, Stiffness & Damping components in the equation of…

Questions - 1 1.Design a warehouse building located in chennai using STAAD Pro connect edition.The specification must be as  follows: Width = 30m                                                                                                                                                                               …

Questions - 1 a)   b)    c) What is the mode of failure or damage of the beams in the figure above?Are the damages repairable?Elaborate   Answers Introduction: The Crack identification in structures by detecting changes in their dynamic behavior has been studied in the past, and various methods…

Question Design a multi-storey Residential Building located in Bangalore using STAAD Pro Connect Edition. The specification must be as follows: Building Floors                    : G + 6 +R Plan Dimension                   …

Questions -1 State the primary load cases to be considered for design. What is One – Way slab? What is the value of unit weight of structural steel and soil? Name few sections that can be defined using Properties tab in STAAD Pro. Define Primary Beams. Answers: 1.1.State the primary load cases to be considered…

Attached all the files are in pdf below  ....

1)Aim: To use the architecture/ structure project file  to export revit architecture and structural model to Naviswork cache file Tools Used: File,Export,NWC Procedure: Open an architectural model created in week 8 Go to file Click on export and save as NWC Repeat it for both architctural and structural …

1)Answers: A)Aim:Write the steps involved to upload a .std file through web mail? Introduction :  STAAD pro ( Structural Analysis and Deign program is the abbrivation for the STAAD it is the connected version new version used to analize the RCC structure and steel structure by using this software ) It Include…

1)Aim: Need to create sinusoidal point then curve from the point and then create surface Introduction: By using dynamo created a sinusoidal point then created a curve from the point and converted into the surface Procedure: Step 1) Open Dynamo Open Revit software In new architectural template Go to manage tab, click on…

1) Aim : To select type of the structure for modelling in the Revit software. Introduction : Depending upon the type of structure the design consideration of building for the modelling purpose vary. So it is important to clarify the type of structure before starting any project so that it will serve…

Answers: 1)AIM : To model a ceiling to the previously created project with the help of architectural tab above the walls at first floor level.  TOOLS USED : Architecture tab, ceiling, sketch ceiling,pick lines, properties.  PROCEDURE :  a) In the project file saved from week 3, click on ceiling tool in architecture menu.…

Aim: To create a 3 dimensional model of the residential building with a rendered view using AutoCAD software. Introduction: Various commands used QNEW command UN command LIMAX command Z command REC command Offset command Trim command Line command CO command MOVE command LA command 3DROTATE command PLAN command Region command…

....i have attached the screenshots file below...

... i attcvhed the screenshots file  below......

i attched the screenshots file to given below.. 

....i attached the file for screenshots below...

AIM :           TO DRAW RESIDENTIAL BUILDING OF DIMESIONS 60' X 20'  WITH THE FOLLOWING DRAWINGS 1) ARCHITECTURAL DRAWINGPLOT DRAWINGGROUND FLOOR PLANFIRST FLOOR PLANELEVATION VIEW 2) STRUCTURAL DRAWINGSECTION VIEWFOOTIG LAYOUTCOLUMN LAYOUTBEAM LAYOUT   INTRODUCTION : THE RESIDENTIAL BUILDING TO BE DRAWN WITH PLOT DIMENSIONS…

Sketch G+1 residential plan according to Vaastu Shastra and Calculation of Loads as per IS code Sketch a G+1 floor residential plan, according to Vastu shastra, and list down the names of the structural drawings required to be provided to the site for construction. Also, assume the sizes of the structural elements (Column,…

AIM: To Calculate the Concrete Mix Design for M35 grade concrete with fly ash & M50 grade concrete without Fly ash INTRODUCTION: Concrete mix design is the method of finding the precise proportion of cement, sand and aggregates for concrete to achieve the target strength in structures, therefore concrete mix design…