Week 10- Assembly Workbench

Objective:To route the Wiring harness on the given car body and Prepare flatten view drawing in CATIA V5.Process:Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system…

 AUTOMOBILE HOOD DESIGN:   Here we are going to understand and design the concept of front-mounted engine’s hood according to the standards. The hood or bonnet is the hinged cover over the engine of motor vehicles that allows access to the engine compartment, or trunk for maintenance…

UNDER BODY COATING : Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of years,…

Hyundai Venue S Engine and Transmission Engine Type                           1.2 Kappa Petrol Engine Displacement              1197 cc Max Torque                   …

Objective:            To route the Wiring harness on the given Engine and Prepare flatten view drawing in CATIA V5. Process: Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system definition.…

Objective:  Flatten the harness assembly completed in the "week 4 challenge".      • Place the flattened view on the drawing sheet.      • Ensure bundles with protective coverings has different visuals on the drawing view. Process: Defining the cad files:  Open the igs…

Objective: To route harness layout in Electrical workbench.  Process: Defining the cad files: Open the igs files and create a midpoint on the face using point type as between. Now we can create an axis system to the point we have created by using the command axis system definition. Make sure the x-axis is pointing…

Objective: To route the harness layout in the Electrical workbench using the connectors, •DT06-4S • DT06-6S .DT06-2S • DT06-08SA Add protective covering on all branches connected to DT06-2S & DT06-4S connectors and keep the end extremity at 30mm. Process: DT06-4S: • Open the DT06-4S igs file and create a midpoint on the…

Q1. Download following cad data & define it as Electrical support using Electrical Part design Workbench. Define all the necessary properties. Objective: To define clip cad as electrical support using electrical part design workbench. Process: First, we have to define the geometry parameters of the P clamp. We need to…

Objective : To define connectors & Connector clip cad as Electrical connectors using Electrical Part design Workbench. 1. Deutsch DT06 – 08SA : Process: Open the Deutsch DT06 – 08SA igs file and create a midpoint on the face using point type as between. Now we can create an axis system to the…

AIM:      To create the 3D Part from the 2D Sketch and Assembly in Assembly Part Design. OBJECTIVE:      To create the Solid part from the 2D Sketch.      All Sketch must should in positioned sketch and also Iso-Constraine.      Ensure Created parts arein Same Folder.      Ensure all assembly are corrected and constrained.…

A Pillar    Ramakrishnan Safran SL, [06-Nov-2022 at 10:27:54 PM]: AIM:       To craete the Solid part from the given Class A surface and Follow the Master section for B Side Feature to creation. OBJECTIVE:        Picture of the sketches with Sketch solving status’s geometry…

1. A detailed report should be done explaining the draft analysis at the Class A surface.  Draft analysis on Class A surface of Door trim Lower -Step 1- Open draft analysis and move the compass to coincide with the Tooling axis  Step 2- Lock the compass and check the radius/angles using the running analysis…

Tooling Axis creation: Using the tooling axis created along the x and y-axis, these tooling axes are used to create the tooling axis by a bisecting method where the two lines and points will be selected as inputs. Draft Analysis: The Draft Analysis command lets you detect if the part you drafted will be easily removed.…

  Tooling Axis creation: Using the tooling axis created along the x and y-axis, these tooling axes are used to create the tooling axis by a bisecting method where the two lines and points will be selected as inputs. Draft Analysis: The Draft Analysis command lets you detect if the part you drafted will be easily removed.…

1.A detailed report should be done explaining the draft analysis and the tooling axis creation. Draft analysis on Class A surface of Switch Bezel below-Step 1- Open draft analysis and move the compass to coincide with Tooling axis as below Step 2- Lock the compass and check the radius using the running analysis option-…

  1. A detailed report should be done explaining the draft analysis at the Class A surface.  Draft analysis on Class A surface of Bumper-Step 1- Open draft analysis and move the compass to coincide with the Tooling axis  Step 2- Lock the compass and check the radius/angles using the running analysis…

  1. A detailed report should be done explaining the draft analysis at the Class A surface.  Draft analysis on Class A surface of Coin holder-Step 1- Open draft analysis and move the compass to coincide with the Tooling axis  Step 2- Lock the compass and check the radius/angles using the running analysis…

1.A detailed report should be done explaining the draft analysis and the tooling axis creation. Draft analysis on Class A surface of Switch Bezel below-Step 1- Open draft analysis and move the compass to coincide with Tooling axis as below Step 2- Lock the compass and check the radius using the running analysis option-…

BASE BRACKET