Week 10 - Challenge 2- Attachment Feature Creation (Dog House)

AIM:- The aim of this project is to model a butterfly valve and to apply GD&T to the different parts of the butterfly valve and the assembly. Parts of Butterfly Valve :- Body of Butterfly Valve Shaft Retainer Disc  Lever Nut Screw Final Assembly 1.BODY OF BUTTERFLY VALVE:- 1.Initially, the sketch for the body of the butterfly…

AIM: To Design the outer upper and lower panel, inner panel with the necessary reinforcements by following the Master section with the design parameter for the given class A surface. INTRODUCTION: The trunk (North American English) or boot (British English) of a car is the vehicle's main storage or cargo compartment, often…

  Title- Design of Roof Objectives- For the Given Roof styling, Develop the essential flanges and reinforcements, provide appropriate dimensions, check for Draft analysis, and submit your section modulus report on the 0-Y section. Start with the creation of a roof ditch area the tool opening angle is only 3 degrees. Do…

AIM: The main objective of this project is to design a fender using a new age design software - NX – CAD. FENDER: The main purpose of the fender is to prevent sand, mud, rocks, liquids and another road spray from being thrown into the air by the rotating tire. TYPES OF FENDERS: <!-- [if gte vml 1]> <![endif]--><!--…

Aim: To find the section modulus of the hood and optimization to improve the overall section modulus.  Use the section from your Hood design and calculate the section modulus using the formula S= I/y.   Section Modulus: The section modulus (S) is geometry property of the cross section used for designing beams and flexural…

AIM To create a complete hood assembly from the given Master sketch and skin data of the Hood outer panel using Siemens NX-CAD. THEORY Car Hood or Bonnet is one of the important BIW parts of the car. It is the hinged cover that rests over the engine of a front-engine vehicle. There are two different types of hoods, they…

AIM: - To create a CAD model for door trim panel's parts by considering the given inputs of class A surface along with master section by following the design rules followed in OEM companies.   OBJECTIVES: -   To create individual tooling axis for the parts and perform draft analysis on the class A surface To form a solid…

Create the Screw boss for the Drill Handle considering the design rules mentioned in the video.  General Guidelines for Bosses:   Draft - 0.5 degrees on the walls of boss   Thickness - Typically 40% of the nominal wall at the base.   Height to Diameter Ratio - 3:1   Radii - 0.25mm maximum radii. 

AIM: To understand the given master section to create a solid body and B-side features for a given class A surface, by considering all the design rules.   1. Tooling axis creation:       To create the tooling axis, I used the 'bisecting' line method. Initially, I extracted two lines from the master section and then I created…

AIM: Create the Door Trim Lower Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model.  Create the Heat Stakes and the locators considering the…

AIM: Create the Dog House for the Door Trim considering the design rules mentioned in the video. Consider the thickness of the part to be 2.5 mm. "C" is where the doghouse contacts the backside of the surface. <!--[endif]--> <!-- [if !supportLists]-->·        <!--[endif]-->Doghouse wall thickness at the…

  AIM: Create the Bumper Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Take the Thickness of the component to be 3 mm INPUTS: Class…

AIM: Create the Base Bracket Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Thickness of the plastic part is 2.5 mm. INPUTS: Class A surface…

AIM: Create the Switch Bezel Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Thickness of the plastic part is 2.5 mm. INPUTS: Class A surface…

.