Week 8 - Challenge 1 - Draft Analysis on a Fan Cover

OBJECTIVE:           Extracting the inner panel model from the given class A surface with all the design and mounting consideraions. And creation of all reinforcements at all the required position, finally draft analysis along the tooling direction. History of Back Door The door or opening of a…

FENDER:                           Fender is the American English term for the part of an automobile, motorcycle or other vehiclle body that frames a wheel well (the fender underside). Its primary purpose is to prevent sand, mud, rocks, liquids, and other…

OBJECTIVE:        Our objective is to create the proper reinforcements in proper locations of the roof as it should with stand the basic amounts of Heat distortion criteria and Snow load condition. Ths whole process involve the following steps to create the proper reinforcement. Creation of all the…

SECTION MODULUS :             Section Modulus is the geometric property of the given cross-section of any shaft or beam structures. It is the direct measure of the strength of the shaft section or the beam section. Higher the section modulus of a structure, the more the resistive it becomes…

HOOD DESIGN:        In order to meet the industry requirements we have to consoder all the design considerations in desiginig a part. HOOD also one of its product, We have to consider the HOOD design in all the criteria. Hood is one of the importent part in the entire car body, which will act as one…

        Underbody coating is usually a dense cladding (often based on rubber) applied uniformly to the undercarriage of the automobile. It is normally sprayed or painted on when the car is just out of the dealership and is clean. But even if you are getting the undercoating applied after a couple of…

What the bench marking is ?          Tear down is a specialized task in automotive benchmark. Tear down reveals the key components and  features of a vehicle or system, which is required to set target for the new vehicle development. Most of the vehicle manufactures…

AIM:         Our main aim is to generate a side door panel From the given class A surface with all B side features ( For mounting Doghouse and push pin; For joining of parts Heatstakes ), and performing The draft analysis on each part. GIVEN CLASS A SURFACE          For the part generation i have followed the folowing…

Complete Body creation with all the engineering features is created and the process is made a presentation and the same is attched below. Along with catia file.

OBJECTIVE:  To design a Door Applique with all the engineering features to be following all the Design rules of making solid part body form class A surface and attaching both locators and Heat strakes to it and performing thr draft analysis on the final body. And also providing slots on the Door attachement surface.…

OBJECTIVE:           We are going to create SCREW BOSS and DOG HOUSE on the given Coin holder and performing the draft analysis on the fianl body.   For the report purpse we are taking already created object whick is Coin holder which is made from the class A surface by performing all the…

RIB CREATION OBJECTIVE:                  We have create ribs  on the coin holder by following all the design rules.And per forming the draft analysis on the final body. And we have listed the rib creation rules below and followed the same. Thickness of the rib should be…

OBJECTIVE:   This is to generate Parting surface and Parting line for the SWITCH BEZEL along the tooling direction.To tha same part we have to create tooling axis,Class B and C surfaces to generate solid part body. And the draft analyisis on the same body. A Detailed Geometrical Sets is provided below for which we…

COIN HOLDER OBJECTIVE: Creating a solid part body from class A surface, performing Draft analyais, creating tooling axis,and class B and C surfaces. Draft analysis on the part body. Ther detailed Geometrical sets tree structure is given in the following image listed of operations performed on the surface. Step 1: Tooling…

Detailed report on the DOOR ARM REST  is submitted in the form of Presentation which is attached below. And all the processes are carried out. CAT part also attached.

SWITCH BEZEL: OBJECTIVE :  From the given SWITCH BEZEL class A surface we are going to extrace Soid part body of 2.5 mm thickness and performing all the daft analysis on the solid part. This Submission consists of following elements  1. Geometrical sets For the complete solid part creation 2. Draft analysis on…

BASE BRACKET Geometrical set tree structure Tooling Axis Objective: Out objective is to create a tooling axis for the given model. A rough visual inspection is carried out for a dummy tooling axis. Then an appropriate Dummy tooling axis is created with Point and Direction command on line creation command. Then among all…

Geometrical Sets Tree structureDraft analysis report Fan Cover in different orientationsIsometric viewFront ViewTop ViewSide viewReport on draft ananlysisThis type of analysis is performed based on color ranges identifying zones on the analyzed element where the deviation from the draft direction at any point, corresponds…