Wiring harness design in CATIA V5 - 3D modeling Week 2 Challenge

1 The main pillar cleares along with the main tooling axis . 2 dog house and ribs clear along with the side core axis. 3 Mastersection matches with the solid created . STEPS OF CREATION  1 CREATED B SERFACE 2.5MM FROM A SURFACE 2 CREATED C SURFACE ALONG WITH REFERENCE TO A SURFACE  3 CREATED DOG HOUSE WITH MASTER…

AUTOMOTIVE WIRING HARNESS FOR BACKDOOR     Aim: To route the wiring harness on the given backdoor assembly and prepare the flatten view drawing in CATIA V5.   Objective: The objective of this project is to route the wiring harness and prepare flatten view drawing for the Backdoor of the car. All types of…

Route the Wiring harness on Given Engine and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices studied in this course shall be demonstrated in design.. ENGINE WIRING HARNESS ROUTING                         …

 1 Assy to flatten  2 Flattening   Cot tubes are not updated due to software errors i have attentend the session also but its not resolved.   Drawing  Thank you    

 1  Bundle continuity  Annotations Warnings CAT Part Generation MAin ASSy Thank You      

1) To Route the following harness layout in the Electrical workbench. 2) Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Given: CAD data of the following Connectors:  DT06-4S DT06-6S DT06-2S DT06-08SA Connectors Layout Design: Steps to be followed: 1. Download connector…

Create center points on entry and exit section of p clip . wrt the the rubber casing that is used to protect the wire.     Create 3 planes : basepalne , entry and exit point plane use  Electrical part Design use support definition  2: Download following Back shell cad data & define it as Electrical…

CONNECTOR DEFINATIONS IN CATIA V5 1. Deutsch DT06 – 08SA Connector connection point             Create midpoint on the contact face which will be normal to wire bunddle insertion.   Craete Axis System with respect to the point which we have created and defining the axis direction…

FENDER DESIGN - WHEEL ARCH CALCULATION: OBJECTIVE: Calculate the Wheel Arc area of European Standard and prove whether the car will pass the standards or Not.INTRODUCTION: The wheel arch is an arch-shaped cavity in the body of a vehicle, which houses a wheel. It has two important functions. It serves for the safety of…

Fender Design 

Sction Modulus for Hood Is Defined As follows:- Minimum Inertia I  distance between the neutral axis and the extreme end of the object y     Moment of inertia(min) = 1.09e+006mm4 Moment of inertia(max) = 1.425e+008mm4 Y= 238.866 S=I/Y S=1.09e+006mm4/238.866 S=4563.227mm4  

                                                                                           …

UNDERBODY COATING   Underbody Coating is a sprayable coating, which protects the bottom surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are…

AUTOMOTIVE BENCHMARKING Benchmarking is the process of comparison of similar products on some dimensions of performance Automotive Benchmarking is the process of analyzing the choices of similar products based on the selection factor and deducing it to final conclusion. CUSTOMER  Mr. D.S. Pughazhyendhii is a…

                                              RIGHT SIDE FRONT DOOR TRIM STEPS INVOLVED IN CREATION OF FINAL PROJECT : Check the A surface given as the input. Check the mastersection for dimentions and thickness.…

1 Quick return mechanism   2. CV Joint

THE PART CLEARS ALONG WITH TOOLING DIRECTION  LOCATORS ALSO CLEARES ALONG WITH THE TOOLING LINE.

1 surface a cleares the part along with the tooling axis    occured a problem in creation of c surface  PLEASE PROVIDE A FERFECT VIDEO SUPPORT ON THE CHALLANGE ITS VERY DIFFICULT TO CREATE C SURFACE  

1.A SURFACE CLEARES THE MOLD ALONG THE TOOLING DIRECTION  2. CREATED THE RIBS AS PER DESIGN RULES . 3. CREATED THE SCREW BISS AS PER THE DESIGN RULES  4 CREATED A FINAL SOLID PART  5. SOLID PART CLEARES ALONG WITH TOOLING DIRECTION.

1 dRAFT CLEARES THE PART ALONG THE TOOLING DIRECTION  2. CREATED THE PARTIONG SURFACE AS B SURFACE. 3. CREATED THE CORE BLOCK  4. CREATED THE CAVITY BLOCK  5. INTERSECTION VIEW OF THE PART FILLING SECTION. 6. FINAL MOLD OF CORE AND CAVITY

1    Detailed Report Steps  1. Created a tooling axis on the base surface  2. Created a B surface With Reference to A surface by 2.5mm 3.Sweeped the C surface along 90 Degrees to the A and B Surface  4 Draft analysis done with the tooling axis with 3degrees Draft.  

1 

1.