Wiring harness design in CATIA V5 - 3D modeling Week 5 & 6 Challenge

Electrical definition  Electrically defined the part to use it as an electrical component to connect with the bundle connection and also with corrogated tube as per the requirement.  the required connectors are need to be defined by electrically by declaring the point and axis system for the desired conductor to prepare…

Electrical definition  Electrically defined the part to use it as an electrical component to connect with the bundle connection and also with corrogated tube as per the requirement.  the required connectors are need to be defined by electrically by declaring the point and axis system for the desired conductor to prepare…

Preparing the Drawing in wiring harness is the different from the drafting we used in plastic products. this the wirings are need to be flattened with the help of wiring harness flatenning work bench.  Once the wiring harness is done we need to give the dimension to the designed product is the major roll in design…

Electrical definition  Electrically defined the part to use it as an electrical component to connect with the bundle connection and also with corrogated tube as per the requirement.  the required connectors are need to be defined by electrically by declaring the point and axis system for the desired conductor to prepare…

   Catalogue:  catalogue is the storage area which we can stor the defined component to reuse again same we need. it can store all the type of connectors and even carogated tube we can store and reuse again. Electrically define: the required connectors are need to be defined by electrically by declaring…

p clamp It's the most user-friendly, versatile, and rugged p-clamp for fastening and fixing cables, Mostly we are using P clamp is for fixing the component to stop the movement and avoid the unnecessary sound produsing from the engine compartment.  Tyco 1738312-1 Corrugated tubes Corrugation of tubes can increase…

Deutsch DT06 – 08SA   We are taking the model previously provided in the te link pointing the connector point and axis tpo the determination to where the connector is going to connect at the centre point and create the axis system to be created with that point and allocate it to be bundle entry point with the…

Report: Back Door: AIM:       To design a back door of the given surface of the product. Developing the given surface Under repairing work to start the design, ensuring the components to be added to get finished Back Door. SOFTWARE USED: CATIA V5 INTRDUCTION      Back door in a car also…

AIM:  TO  Assemble and apply GD&T to the butterfly valve assembly drawing BUTTERFLY VALVE: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When…

ROOF DESIGN Normally the roof is present at the top of the vehicle body that prevents the passenger from any incident, in addition to this roof we are proviting that support with the bow roof1 Bow roof 2 and the center roof to given the additional strength to the component, basically the sheet metal component to prevent…

As per the given master section i designed the fender part eith the recommended joints provided the fender mounting area is the main substance to attach the surface with engine compartment thus it should available at the extra strenth of the substance which we can add two or three joints in that area is sufficient baffle…

Fender wheel arch there are some of regulations to follow for the fender design to satisfy the various region costomers which are UK based costomer, Japan based costomer and europe based costomer. in this regions the government regulations are following different which we are following the standards are 10 mm gap regulations…

Section modulus is a geometric property for a given cross-section used in the design and there is the calculation of inertia to be included that increase in the moment of inertia which increases the section modulus value   section modulus is the ratio of moment of inertia to the distance between the neutral axis and the…

Hood and its component  Hood is basically designed for engine cover for a car and it acts also designed for protection during accident. By which the emboss is designed like outward portion to avoid maximum impact which comes towards the passengers. Emboss plays a major role to save the passeners.  It should be designed…

preparing solid body separatly as parts and getting into a single product file to generate this as a required product design, so we need to prepare a separate body and drafting also fro clear view of understanding.    

Draft analysis Draft analysis  is a portion of finding the good production product. mainly it works for saving the product from damage. basically we follow standared minimum drafting angle which is 3'. thus the product should design above drafting angle for the better output. Attaining blue colour from the analysys…

Draft analysis Draft analysis  is a portion of finding the good production product. mainly it works for saving the product from damage. basically we follow standared minimum drafting angle which is 3'. thus the product should design above drafting angle for the better output. Attaining blue colour from the analysys…

 drafting angle it is the minimum angle that which we follow for creating the surcace for attaining proper production output draft analysis  which allows us to easily analyze a part for proper draft angle to avoid damage for the poroduct vduring manufacturing Tooliong axix controls how we want the tool to orient…

Draft analysis Draft analysis  is a portion of finding the good production product. mainly it works for saving the product from damage. basically we follow standared minimum drafting angle which is 3'. thus the product should design above drafting angle for the better output. Attaining blue colour from the analysys…

Tooling Axis In this part we are not getting proper tooling axix because of there is no drafting portion is present all the portion are present with 90' only so, there is simple tooling axis along the axis  Draft analysis In this design the draft analysis is done without attaining the minimum draft angle

 drafting angle it is the minimum angle that which we follow for creating the surcace for attaining proper production output draft analysis  which allows us to easily analyze a part for proper draft angle to avoid damage for the poroduct vduring manufacturing Tooliong axix controls how we want the tool to orient…

REPORT  DRAFT ANALYSIS  Draft analysis is a portion of finding the good production product. mainly it works for saving the product from damage. basically we follow standared minimum drafting angle which is 3'. thus the product should design above drafting angle for the better output. Attaining blue colour from…

Definition under body coating is nothing about the layers of deposision which we are using for the vehicle's outer and inner of BIW surface. this may contains  electrolyte deposision, sealent, paint which we are using as rust resistance for the vehicle and prevent from it. Method of flow  we having the fixed…

Benchmarking    Benchmarking is purely comparing the products quality, design, perfomance,safety, reputation of an organisation the positive and the negative sides hidden from a product, which is comfortable in all way, here we are going to compare the given product which is five seating budget car in 8 to 10…