Wiring Harness Design in CATIA V5 - 3D modelling week 7 challenge AIM:…
Deepak Guttula
updated on 06 Aug 2022
Project Details
Leave a comment
Thanks for choosing to leave a comment. Please keep in mind that all the comments are moderated as per our comment policy, and your email will not be published for privacy reasons. Please leave a personal & meaningful conversation.
Other comments...
Read more Projects by Deepak Guttula (29)
Project 2
Aim: To route the wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Objective: This project shows that the route the Wiring harness on Given car body and Prepare flatten view drawing in CATIA V5. Application of all Packaging rules, Industry best practices for the harness design.…
19 Sep 2022 04:08 AM IST
Project 1
Aim: To route the wiring harness on given Engine and flatten view drawing in CATIA V5. Objective: The objective of the project is to route the wiring harness on given Engine and prepare flatten view drawing in CATIA V5. All types of packaging rules have to be considered while routing the harness. Also, Industry best practices…
14 Sep 2022 04:29 PM IST
Wiring harness design in CATIA V5 - 3D modeling Week 4 Challenge
Aim: Route the harness layout in the Electrical workbench based on the input. Add protective covering on all branches connected to DT06-2S & DT06-4S connectors. Keep end extremity at 30mm (from connectors end) The above picture shows the 2D schematic layout of the required harness. DT06-4S (QTY-2) DT06-6S (QTY-1)…
30 Jun 2022 02:51 PM IST
Roof challenge
Aim: To modify for the given roof styling skin data, Develop the essential flanges and reinforcements, provide appropriate dimensions and check for Draft analysis. It also performs the roof calculations using by snow load Prediction formula and heat distortion of the Bow–roof prediction Formula. …
07 Feb 2022 09:36 AM IST
Section Modulus calculation and optimization
Section Modulus calculation…
28 Jan 2022 02:34 PM IST
Fender Design - Wheel Arch Challenge
Aim: This project shows that examine the given fender wheel arch design to verify if the wheel arch of the fender meets the European standards. Fender Wheel Arch: Fender Wheel Arch is the sem-circular part positioned above the wheel of the vehicle. The most important body was a change that the…
22 Jan 2022 09:13 AM IST
Underbody Coating
Underbody coating and its purposes…
29 Dec 2021 04:00 PM IST
Benchmarking
…
29 Dec 2021 10:27 AM IST
Radar Mast & Final Assembly of Yacht
1. Radar Mast and Final Assembly of Yacht: Radar Mast Assembly of Yacht Render 2. Introduction: The project gives detailed instruction about the designing of different parts of a yacht-like 1. Propeller 2. Radar 3. BluePrint setup 4. Hull 5. Garage door 6. Front seat 7.…
28 Dec 2021 10:33 AM IST
Photo Realistic Rendering
1. REPORT ON ASSEMBLY OF CHOPPER MODEL DESIGN OF AMERICAN CHOPPER USING SOLIDWORKS 2. OBJECTIVE The objective of the project is to model an AMERICAN CHOPPER using CAD (computer-aided drafting) software-SOLIDWORKS and to render it with SOLIDWORKS visualize to create a photorealistic view of…
28 Nov 2021 04:18 AM IST
Week 11 - Final project
Aim: To Creation of CAD model considering Class A Surface, Nominal thickness, and Attachment strategy. Objective: To Creation of CAD model considering Class A Surface, Nominal thickness, and Attachment strategy. Create the mounting features as per design guidelines in the industry and with master sections Apply material…
12 Oct 2021 04:52 PM IST
Week 9 - Project - Master Section Development
Aim : The objective of this project is to develop a Closed Surface Model using Master Sections To develop attachment features for Fixation of Parts by following OEM Design standards and procedures in CATIA SURFACE WORKBENCH and PART DESIGN Description : Master Section : Master Sections are the guides…
27 Jul 2021 06:53 AM IST
Week 9 - Attachment Feature Creation - Challenge 2
AIM: Create the boss and Dog House for the Centre console coin holder. General Guidelines for Bosses: Draft - 0.5 degrees on walls of boss Thickness - Typically 40% * of the nominal wall at the base. Height to Diameter Ratio - 3:1 Radii - 0.25mm maximum…
18 Jun 2021 08:56 AM IST
Week 9 - Attachment Feature Creation - Challenge 1
AIM: Create the rib for the Centre console coin holder. RULES OF CREATING RIBS: PROCEDURE FOR CREATING RIBS : STEP 1: Create an extract on the base surface. STEP 2: Sketch for creating rib. STEP 3: Extrude the sketch. STEP 4: Height of rib. The height of the rib should be 5*Thickness of components. STEP…
15 Jun 2021 09:44 AM IST
Week 8 - Challenge 5 - Core & Cavity Design
Aim : Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. Procedure : Parting Surface Core Design Cavity Design Draft Analysis Procedure for Parting Surface : Extract the Class A surface boundary lines with boundary option. Extrapolate the Class A surface by 10mm. Trim the extrapolate…
13 Jun 2021 11:42 AM IST
Week 8 - Challenge 4 - Coin Holder Design
AIM: Create the Coin Holder Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Take the Thickness of the component to be 2.5…
11 Jun 2021 10:21 AM IST
Week 8 - Challenge 1 - Draft Analysis on a Fan Cover
Aim: To perform the draft analysis of a fan cover using CATIA V5. Procedure: Steps involved: A)Determining and making the Tooling Axis: 1) Checking the boundary : The class A Surface is first checked for its boundary to find if there is any gaps or opening…
22 May 2021 05:12 PM IST