Creating Architectural and Structural model with 3D rendering using REVIT

AIM:-To Create and Analyse the given building in ETABS 2018, the structural model has to be prepared in accordance with IS 1893 and as per IS 13920. To design the pile cap and pile reinforcement details,Tie  beam  connecting the pile caps, to sketch the column reinforcements, to produce the framing plan and beam…

AIM :     To Model the isolated footing provided in week 11 challenge on SAFE. Analyze and design it to verify the size, depth and steel provided as per calculations. INTRODUCTION :      Foundation design is the creation of a construction plan for a building foundation. It is a highly…

Aim: To manually calculate the spread footing dimensions and reinforcement details with respect to limit state design of soil and structure.   Calculation of Gross soil pressure: Unfactored load = 2000/1.5 = 1333 kN Assume the thickness of footing (t) = 0.5 m Depth of footing as given in data (h) = 2 m, So soil surcharge…

Aim:- To model and analyze the G+7 residential building from the given architectural drawings using the ETABS 2018. Introduction:- ETABS is an engineering software product that caters to multi-story building analysis and design. Modeling tools and templates, code-based load prescriptions, analysis methods and…

Aim: Detailing of shear wall Procedure: Step 1: The provided ETABS model is analysed and the shear wall design is run as shown in the figure below. Step 2: The mentioned shear wall is labelled as P1. The design results of pier P1 is extracted as shown below. From the obtained results, it can be seen that a boundary zone…

Aim: To Providing details of longitudinal reinforcement for the two columns from foundation to terrace level. Step 1: 1) Open a G+4 Etab file 2) Click the Concrete Frame Design tool 3) Select the Display Design Info option 4) Choose design output as Longitudinal Reinforcement Step 2: 1) After Selecting the Longitudinal…

ANSWER:- Aim:- To design the beams in detail from the Etabs 2018.             To provide details of longitudinal and shear reinforcement for the given two continuous beams.             To calculate the value of maximum shear force in any one of the spans…

Aim: To model the buildings from A to K as per the details given below: To to carry out a comparative study of these buildings for seismic forces. Introduction: Every building has a number of natural frequencies at which it offers minimum resistance to shaking induced by external effects and internal effects. Each of these…

AIM: ETABS modelling of a 25 storey building Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey height of 3 metres. PROCEDURE:  STEP1 Open E-Tabs…

1 Ans: As the structure is more restrained it will be more shrinking, expanding and cracking. There will be more floor shrinkage and expanding in structure A whereas there will be minimum cracks in structure B and C. The shear walls in the structure also decide whether the floor vibration is more or less in the structure…

1.Symmertry Having a look over the aspects of symmetry of the framing plan, it is observed that the distribution of mass,Stiffness is across the plan;it is observed that the distribution of mass, stiffness is across the plan.It is considered for one of the good Symmetrical aspects.This tends to reduce the horizontal displacements…

Procedure: Step 1: For mode 1: We know that  =(0.334)+(0.641)+(0.895)+(1.078)+(1.173) x m  Similarly Mode 2 = m2 = 3.861m Mode 2 = m3 = 3.861m Mode 2 = m4 = 3.861m Mode 2 = m5 = 3.861m For the calculation of Ln: L1 = ( 0.334  0.641  0.895  1.078  1.173 ) x       …

1. Differentiate Static analysis and Dynamic analysis by proper representing pictures            STATIC ANALYSIS          DYNAMIC ANALYSIS 1. Load is not variable with time and neglected due to slow applying of load. 1. Load is variable with time due to fast applying…

1 : a)       OBSERVATION FROM THE IMAGE :- As we can see that,Concrete crushed and the reinforcement is fully visible  Concrete fall upto the rebars which may be a sign of rupture Beam top portion looks safe because of the flange advantage from slab  The crack developes from bottom to top means…

) AIM:  To Exporting the Revit architecture and structure model to Navisworks Cache file as discussed in the video. PROCEDURE: First of all we have to install the software form autodest website. Go to Autodesk website Search Naviswork export utility and download 2021 version Click run and extract it.…

Introduction: Dynamo is an open source visual programming language for Revit, written by designers and construction professionals. Its a programminglanguage that allows you to type lines of code;  while also creating an algorithm that consist of nodes.   Using dynamo work can be carried out with enhanced…

Q1) AIM:  Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School. ANS) OFFICE BUILDING Q2) AIM :  Assume reasonable assumptions for geographic…

1) Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level.     AIM:- To model a Ceiling from the architecture tab above the walls at the first-floor level.     INTRODUCTION:- The creation…

NTRODUCTION: The main objective of this project is to understand about to create a Plan in 2D, then convert it into 3D using AutoCAD 3D, applying materials and rendering. AutoCAD is primarily used for generating 2D sketches. While it is possible to create 3D objects, AutoCAD is built around a flat, sketch-based interface.…

AIM:- To create a 3D isometric view of the given building with plan and elevation.    INTRODUCTION:-  An isometric drawing is a 3D representation of an object, room, building or design on a 2D surface. One of the defining characteristics of an isometric drawing, compared to other types of 3D representation, is that the…

AIM :         To create a 3D Furniture elements using the various commands in Auto CAD. INTRODUCTION BY 3D VIEW : The process of creating a mathematical representation of any surface of an object in three dimensions by using special software. A 3D model can even be represented as a two dimensional image…

1Aim:     To Creating the layout of floor plan and section of challenge 7 project using Autocad Introduction:  The main objective of this project is to understand about the viewports in Auto CAD. There are two types of viewports in AutoCAD. Model space viewports  and layout space viewports.…

  Aim: To Create the Kitchen Layout and to Also, use proper dimension techniques to dimension the kitchen layout. Also, insert text wherever required. All dimensions are in mm. Procedure: step 1: units are set to mm limits and limax are also set zoom comand is also used Steps for drawing Below Counter Plan Open…

Aim: To create: Template, inserting text and attributes Doors of warehouse and placing it in blocks Electrical legend and making it blocks Different types of door for residential project Drawing bars, making it as block and making it as a table as bar bending schedule.   Commands used:  Block. Insert. Attributes.…

1 ANS:                                                                                         …

1 ANS:                                                                                         …

 ANS:   Commands used  are Line 'L' Copy 'CO' or 'CP' PolyLine 'PL' Trim 'TR' Offset 'O' Isometric View Text Dimension 'DIM' Dimstyle 'D' MATCHPROP 'MA' Move 'M' Mirror 'MI' Fillet 'F' Erase 'E' Rotate PTYPE POINT CIRCLE RECTANGLE Q.1)      Decimal       …

        Aim: To draw cross section of wall over footing.                                                                     …

AIM:   * To Create the geometries from P1 to P2 using all the coordinates system methods and P3 to P10 by any one coordinate system   * To Draw the profile and the trusses using any coordinate system methods. The dimensions are there for reference.   INTRODUCTION: Before going to the drawing, we should know…

1   ANS:                                                                                       …

1  ANS: To caluculate the concrete mix design fo M35 grade concrete with fly ash&M50 grade concrete without fly ash.  OBJECTIVE: The objective of this project is to produce a mix  desifn for M35 grade concrete conataining fly ash and M50 grade concrete. the mix will be prepared as per is METHOD: concrete …