Creating Architectural and Structural model with 3D rendering using REVIT

Aim - Comparative study of different storey buildings for Seismic forces. Introduction - studying the Factors influencing the dynamic characteristics of a building, Factors influencing the Natural Period of a building, Factors influencing the Mode shape of oscillations Procedure -  we need to create 10 different…

Aim - Modelling of 25 storey building with the specified properties using ETABS Introduction - Model a 25 storey building on ETABS with structural properties as specified below. Ground floor or plinth floor level can be taken at a height of 1.5 metres from the base. Each of the successive 25 storeys has a storey…

Q.1 Aim - Conceptual design of a building with columns and shear walls Restraint of Floor shrinkage Observation - For option (a)- Full restraints are provided at all corners For option (b)- all the Corners are left free but there are restraints provided along the edge For option (c) - There are Non-uniform restraints…

 1. Aim -  Understanding Concept on positioning of Columns Comment on framing plan in X direction with respect to symmetry -If we divide the plan vertically in the middle both the sides look mirrored so we can say the given plan is symmetric in X directionComment on framing plan in Y direction with respect to symmetry…

Q.1 A) Observation - Concrete is crushed and the reinforcement is visibleConcrete spalled beyond the reinforcement which may be sign of ruptureNo damage has found on the top of the beam because of the flange advantage from slabThe cracks are developed from the bottom that means bar yielding occurred in support bottom only…

Q.1 Aim - Usage of Navigation tool , Timeliner and Clash Detection test using Naviswork Introduction - Export the Revit architecture and structure model to Navisworks Cache file Procedure -  1. first open revit and open the file you want to export  2. once the file is open go to the 3D view of the model 3. then go to file…

Q.1  Aim - Creating Conceptual mass in REVIT and Creation of Sinusoidal curve and a Parametric tower using Dynamo Introduction - Using Dynamo create a set of sinusoidal points and create a curve and create a surface out of the curve. Procedure - To create sinusoidal curves first open Revit then go to the…

(Note - I am submitting this challenge for 2nd time now. yesterday i submitted it but it is showing as not submitted.) Q.1  Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings …

Q.1 Select the type of structure you want to build from one of the three below:        a. Multi-Unit Residential Apartment        b. Office Buildings        c. School I selected primary school building. Q.2  Assume reasonable assumptions for geographic and…

Q.1  Aim - 3D Creation of Celing for a house plan using REVIT Introduction - Based on the project saved from Week 3, proceed from the First Floor Level. Model a Ceiling from the architecture tab above the walls at the first-floor level Procedure -  1.open the model created in the week 3 challenge 2.then…

Aim - Creating a 3D rendered model for a Residential Building in AutoCad Introduction - for 3D rendering i used the plan which i created while autocad project 1. I 3d modelled that plan and redered it using AutoCAD 3D commands Procedure - 1. open Autocad 2. open the plan and switch to 3d modelling workspace 3. then…

Q.1  Aim - Creating 3D Isometric view of various structural elements in AutoCAD Introduction - draw the plan and elevation of the plan as shown in fig by using AutoCAD 3D cammands Procedure - 1. open auto cad  2. set the work space to 3d modelling 3. then prepare 2d plan as shown in fig 4. then extrude the…

Q.1  Aim - Creating 3D Models like Furniture, Footing, Girder, Column drop with panel and Gable Wall in AutoCad Introduction - creating furniture in 3D AutoCAD using necessary coomands  Procedure -  1. open AutoCAD  2. set the units  3. set the workspace to 3d modelling 4.by using polysolid…

Q.1  Aim - Creation of Multiple viewports, Scaling the drawing and setting in Template in AutoCad Introduction - create the layout of drawings using multiple view ports and template Procedure -  1. open the drawing of which u want to create the layout  2. then set the page through page setup manager…

Q.1  Aim - Creating Kitchen layout in AutoCAD Introduction - created kitchen layout by using line, offset, fillet, extend and then hatched the drawing as shown in the fig Procedure-  1. open autocad 2. set the units  3.draw the kitchen layout as shown in fig  4. use the given dimension and by using…

 Q.1 Aim - Create the templates as shown in Figures.  Introduction - prepare the drawing template as shown in fig. and then make it it a block. Procedure - 1. open the autoCAD 2. set the units 3. prepare the table as shown in fig with the help of line 4. then use single line text and fill the content in…

Aim - Creating an Architectural plan for the provided plot size and develop relevant basic structural drawings. Introduction - Create architectural plan in plot size 18.3m X 6m and facing east use different tools to draw the plan and then using proper dimension techniques give the dimension. draw structural drawing.…

Aim - Creating a Layout, Section and Elevation with dimensions using AutoCad Introduntion - create plan and sections using line, x line, dimensions, text, leader commands and trim, offset, copy, fillet etc. modication commands. Procedure - 1. open the AutoCAD software 2. start with setting the units to decimal 3.…

Q.1 Aim - Creating a Wardrobe detailed drawing using AutoCAD. Introduction - Draw warbrobe by using different commands like line rectangle and modification command like offset, fillet, trim and then provide proper dimensions. Procedure -  1.open autoCAD 2.set the units to decimal 3.start with drawing the front…

Q.1 Aim - Create a column schedule as shown in the figure. Introduction - Create a column schedule using line and text commands. Procedure -  1. open the AutoCAD  2.Set the units to imperial 3.Prepare the table by using line command 4. Create a new text style font name: romans.shx; Height: 8”,…

Q.1 Aim - Creating a Residence Layout using AutoCad Introduction - Drew residence layout using layers, line command etc. modification commands like offset, fillet, trim, extend etc. Procedure -  1.open AutoCAD  2. set the units to engineering. 3.first draw x line vertical and horizontal. 4.then offset…

Q.1 Aim - Drafting various geometries using AutoCAD commands. Introduction - Drew given geometry by using line and circle command. Procedure -   1. open AutoCAD  2. set the units to decimal 3.By using line command first draw 3.00 line 4.then by using polar snapping 45,90,135.. draw the inclined line 2.12 length…

Q.1 Aim - Drawing c/s of load bearing wall by using AutoCAD Itroduction - using necessary commands like, line, rectangle, polyline  and modification tools copy, etc.  i drew c.s of load bearing wall. Procedure - 1. read the drawing carefully. see for all the dimensions needed to draw the fig. 2. open autoCAD…

Q.1   P1 using all the coordinates system methods - Absolute coordinate system - Relative coordinate system - Relative polar coordinate system - Q.2 P2  using all the coordinates system methods - Absolute coordinate system -   Relative coordinate system -     Q.3  P4 - …

G+1 floor residential plan, according to Vaastu Shastra list down the names of the structural drawings required to be provided to the site for construction - Centre line drawing - Footing and Column layout with reinforcement details -  Column Schedule with reinforcement details - Plinth beam layout with reinforcement…

Design of concrete mix of M30 grade using fly ash – Required Data – Cement – Type of cement OPC (43 grade) Specific gravity 3.15 Max cement content IS 456:2000 Cl.8.2.4.2   Site Condition – Exposure Severe Workability 120mm Method of placing Pumping Degree of supervision Good   Admixture…